Boat Outfitting - Jack Plates

Replacement Actuator for ATLAS™ Jack Plates Post March 2014Features: Allows customers to remove the motor from a faulty AHJACT-3-DP and replacement it with a new one More cost effective than replacing the entire actuator WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Z-Lock™ 4" Set Back Manual Single Adjust Jack PlateZ-Lock Jack Plate Revolutionary Design Adds Strength and Stability. The excellence of T-H Marine's HI-JACKER™ jack plate series continues with the Z-Lock Manual Jack Plate design upgrade.Features: Z-Lock™ Jack Plate Design Eliminates Side Slippage Matching slotted extrusions LOCK side plates in place Strong Aircraft Grade Aluminum Full ½” Material For Strength Handles All V6 and V8 Outboards up to 300 hp Easy to Adjust From Top of Jack Available in 4", 6", 8", 10" and 12" setbacks 5" of Vertical Adjustment WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

ATLAS™ Jack Plate Replacement Rocker SwitchGenuine Replacement Parts for Atlas Hydraulic Jack Plate. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Replacement Relay Harness for Hydraulic Jack Plates 2014+Genuine Replacement Part for Atlas Hydraulic Jack Plate.WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

ATLAS™ 8" Set Back Hydraulic Jack Plate - Glossy Black AnodizedThe Atlas revolutionary design meets the demands of today's high performance outboards. The one piece design, featuring the innovative Rod and Slot lifting system, will handle the stresses from the heaviest and most powerful outboards, up to 300 HP or 625 pounds, on the market today. All of the hydraulics are built into the jack eliminating the necessity of installing pumps and reservoirs inside the transom. The all new hydraulic unit is fast too..lifting from bottom to top in 8 seconds!WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

ATLAS™ 8" Set Back Hydraulic Jack Plate PolishedRated for engines up to 300hp or up to 625 pounds dry weight.5 REASONS YOU SHOULD CHOOSE THE ATLAS™ HYDRAULIC JACK PLATE ATLAS™ is truly the best hydraulic jack plate in the world ATLAS™ is factory installed by more boat manufacturers than any other plate ATLAS™ is used by more professional fisherman than any other hydraulic jack plate ATLAS™ is the #1 selling hydraulic plate in the world – sold & serviced by more outlets ATLAS™ hydraulic actuator is made in the U.S.A. vs. our competitors being from China 6 WAYS THE ATLAS™ CHANGED HYDRAULIC JACK PLATES FOREVER ATLAS™ is made by T-H Marine/CMC, who were the FIRST to offer an actuator inside the jack plate – the competition copied ATLAS™ was the first plate to offer predrilling for shallow water anchors – the competition copied ATLAS™ was the first and only plate that did not require regular grease lubrication – the competition design cannot do that ATLAS™ was the first plate to include a heavy duty safety cable to protect boaters from engine entering cockpit upon failure ATLAS™ was the first plate to offer a very simple actuator replacement in the field ATLAS™ was the first major development in hydraulic jack plates in over a decade – spurring hydraulic jack plate improvement WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

PT-35 Tilt & Trim for Up to 35hpElevate your boating experience with the CMC PT-35 Tilt & Trim, designed for up to 35 hp motors. This lightweight, durable unit enhances stability and performance, ensuring better handling and lower fuel consumption.Features: Rated for 35 hp power and smaller motors 5 1/2" Setback to Enhance Boat Stability and Performance 1/4" 6061 T6 Extruded Aluminum Construction with Stainless Steel Fasteners Accommodates Clamp-on or Bolt-on Motors Without the Need for an Adapter Specifications: Power rating: up to 35 hp Set Back: 5 1/2" Trim and tilt: 84° Inside dimension of the motor mounting area: 11" Electric hydraulic actuator rating: 7853 lbs. of thrust Weight: 24 lbs Electric Hydraulic Tilt & TrimYou Get Power Tilt & Trim, Better Boat Handling, More Speed, Lower Fuel Consumption and No More Back Strain!Note: The inside dimension of the motor mounting area of the PT-35 is 11 inches. Before ordering, please make sure that the maximum width of the clamp mounting feet and/or mounting bolts of the motor that must fit into this area does not exceed this 11 inch limit. Refer to the transom view drawings. Mounting bolts are not included with the PT-35.

Read more less

ATLAS™ 12" Set Back Hydraulic Jack Plate - Gloss Black AnodizedThe ATLAS revolutionary design meets the demands of today's high performance outboards. The one piece design, featuring the innovative Rod and Slot lifting system, will handle the stresses from the heaviest and most powerful outboards, up to 300 HP or 625 pounds, on the market today. All of the hydraulics are built into the jack eliminating the necessity of installing pumps and reservoirs inside the transom. The all new hydraulic unit is fast too..lifting from bottom to top in 8 seconds!WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

8" Hole Shot Plate for Z-Lock™ Jack PlateREVOLUTIONARY...SIMPLE...UNIQUE...EXCITING.These are but a few of the comments coming from users of T-H Marine's HOT SHOT™ hole shot plates. This simple but revolutionary plate easily attaches to the bottom of our jack plate to provide an amazing 18 to 20 percent better hole shot. That's 2 to 3 seconds faster out of the hole. Hot Shot™ does this by dramatically reducing water drag on take-off as well as serving as a center trim tab. An added advantage is the ability to stay on a plane and virtually eliminate porpoising at lower speeds.Models available for Z-LOCK™ manual plates.  Features: Provides Improved Hole Shot Reduces Water Drag at Take Off Reduces Porpoising WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

ATLAS™ 14" Set Back Hydraulic Jack Plate PolishedRated for engines up to 300hp or up to 625 pounds dry weight.5 REASONS YOU SHOULD CHOOSE THE ATLAS™ HYDRAULIC JACK PLATE ATLAS™ is truly the best hydraulic jack plate in the world ATLAS™ is factory installed by more boat manufacturers than any other plate ATLAS™ is used by more professional fisherman than any other hydraulic jack plate ATLAS™ is the #1 selling hydraulic plate in the world – sold & serviced by more outlets ATLAS™ hydraulic actuator is made in the U.S.A. vs. our competitors being from China 6 WAYS THE ATLAS™ CHANGED HYDRAULIC JACK PLATES FOREVER ATLAS™ is made by T-H Marine/CMC, who were the FIRST to offer an actuator inside the jack plate – the competition copied ATLAS™ was the first plate to offer predrilling for shallow water anchors – the competition copied ATLAS™ was the first and only plate that did not require regular grease lubrication – the competition design cannot do that ATLAS™ was the first plate to include a heavy duty safety cable to protect boaters from engine entering cockpit upon failure ATLAS™ was the first plate to offer a very simple actuator replacement in the field ATLAS™ was the first major development in hydraulic jack plates in over a decade – spurring hydraulic jack plate improvement WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

BA-130 Break Away MountThe CMC BA-130 Breakaway Unit is designed for boaters navigating shallow, debris-heavy waters, allowing for safe passage over obstacles. It minimizes damage to both the boat and motor while providing up to 45 degrees of movement.The BA-130 is rated for outboard motors up to a maximum of 130 H.P. The unit is mounted between the boat transom and the outboard motor. It is designed to help minimize damage to the outboard motor and boat transom only when an obstruction is encountered while running at speeds under 5 M.P.H. in the forward direction. As it encounters an obstruction, momentum causes the motor to deflect and rotate up to 45 degrees to slide over the obstruction. A drawbar spring is incorporated in the unit to help return the motor to its normal position. The drawbar spring also holds the motor at the normal position while operating in the reverse direction at low R.P.M. The BA-130 is not designed to encounter obstructions while the boat is being operated in the reverse direction.The unit is pre-drilled with the standard B.I.A. hole pattern. For motors that have clamps with thumb screws, CMC part #13022 Transom Clamp Adapter is required. Product weight is 28 pounds (shipping weight is 33 pounds) and carries a limited 1-year warranty against defects in workmanship.Features: Rated for outboard motors up to 130 H.P. for enhanced versatility. Enables safe navigation at speeds under 5 M.P.H. in the forward direction. Features spring return technology to ensure the motor returns to its original position after encountering obstructions. Glide safely over submerged logs or debris at low speeds Offers 45 degrees of movement Spring returns the motor to the standard running position Standard B.I.A. hole pattern Specifications: Maximum Horse Power: 130 Recommended Speed: Less Than 5 mph Direction: Forward Only Weight: 28 lbs WARNING: The BA-130 is rated for outboard motors up to a maximum of 130 H.P. Do not encounter obstructions at speeds over 5 M.P.H and only in the forward direction. The BA-130 is not designed to encounter obstructions while the boat is being operated in the reverse direction.

Read more less

Static Jack Plate 5" Vertical ExtensionThe 5-inch vertical Extension enables higher motor mounting, ideal for transitioning from prop to jet drive and enhancing shallow boat performance.The 5-inch vertical Extension allows the motor to be mounted 5 inches higher than the standard mounting height on the transom. It is a must for conversion from prop to jet drive. Another application includes mounting the 5-inch vertical extension on a hydraulic jack plate to raise the motor higher on shallow-running boats that are equipped with tunnel extensions. Constructed of Extruded 6061-T6 Aluminum alloy.Features: Allows motor elevation by 5 inches over standard mounting height Perfect for use with hydraulic jack plates on shallow-running boats Made from durable extruded 6061 aluminum alloy for long-lasting performance Specifications: Vertical Extension Height: 5" Material: Extruded 6061-T6 Aluminum alloy

Read more less