Boat Outfitting - Tools

Acrylic Adhesive - 10-PackCAN NOT SHIP AIR,UPS GROUND ONLYAT-2010 is our biggest seller and is a unique adhesive. It has high viscosity and will hold smaller parts without sagging. AT-2010 cures in 5 - 6 minutes, has a 4 minute working time and develops working strength in 15 -20 minutes. This makes AT-2010 the ideal adhesive for applications which require an immediate high strength bond. AT-2010 has a 6 month shelf life when stored at 72 degrees. We recommend that where ever possible this adhesive be refrigerated. Packaged in a 50ml cartridge and can be mixed by hand or by using our AT-300 gun and mixing tips. The 50ml cartridge will bond 150 - 200 parts.

Read more less

AT-850 Square Mixing Tip f/2010, 4020, & 8040 Adhesives - 4" - Case of 10Weld Mount's AT-850 tip is for use only with the 2010, 4020, & 8040 adhesives. It's unique design eliminates any possibility of the cartridge plugging up as the entry is separated.Features: Square Mixing Tip 4" Long Case of 10

Read more less

Footman's Strap MountThe Footman's Strap Mount is designed to be bonded with AT-4020 Acrylic Adhesive. This strap mount is 3.25" long and 1" wide and holds up to a 1.3" max strap width. This strap is incredibly strong, paintable, and is rated for over 600 lbs. strength. Use it for battery and tank tie downs and mounting heavy hoses and cables or deck mounted for life raft tie downs.

Read more less

AT-6031 Metal Bond AdhesiveAT-6031 is a 10-to-1 metal bonding adhesive. It has high viscosity (cures in 10–12 minutes), has a 6-minute working time, and develops working strength in 40 minutes. AT-6031 develops more than 2,500 lbs. (psi) of tensile strength on most metal surfaces, making it an ideal alternative to welding in many applications.The AT-6031 uses AT-651 mixing tips and comes in a 50mL cartridge. Compared to the previous version, users get 13mL more product at the same price.*AT-6031 has a 6-month shelf life and should always be stored refrigeratedFeatures:The nozzle on the cartridge will never freeze up

Read more less

1.5" Tall Stainless Stud w/#10 x 24 ThreadUtilize the same base as the 1.4" x 20 studs but with a smaller threaded stud inserted into the base. These studs are ideal for mounting wire clamps and securing items which require a smaller stud diameter. These studs can be bonded from either surface of the base plate.

Read more less

White Nylon Wire Tie MountThe AT-3 tie mount is smaller for panel and other small space applications. This part is molded in white nylon and is sized for a #3 wire tie with a maximum width of .20". Average pull strength is about 50 lbs. The square base measures .44" wide. Use this smaller wire tie for runs with only a few wires or where space prevents use of our larger tie mounts. Excellent for mounting compass wires on center console boats and for overhead panel runs.

Read more less

White Nylon Wire Tie MountThe AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull strength of 150 lbs. It's approved for submerged bilge applications. Stop putting plywood in your hull just to have a place to drive wire tie screws. Saves material and labor costs!

Read more less

8040 Acrylic Adhesive with Plunger AT-8040 is a good general-purpose adhesive packaged in a manual plunger cartridge. Simply snip off the two end caps dispense the needed amount of adhesive onto a clean surface and mix it by hand. AT-8040 cures in 10-12 minutes, has a 6-minute working time and develops working strength in 40 minutes. AT-8040 has a 12-month shelf life when stored at 72°. Weld Mount recommends that wherever possible this adhesive be refrigerated. Packaged in a 30ml cartridge this adhesive does not require the adhesive gun or mixing tips. The 30ml cartridge will bond 30-50 parts. Quick Guide (pdf)Owner's Manual (pdf)

Read more less

White Nylon Wire Tie MountThe AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull strength of 150 lbs. It's approved for submerged bilge applications. Stop putting plywood in your hull just to have a place to drive wire tie screws. Saves material and labor costs!

Read more less

AT-651 Mixing Tips for Use with AT-6031 Adhesive - Qty. 10Weld Mount’s AT-651 mixing tip is designed specifically for use with Weld Mount’s AT-6031 adhesive. AT-6031 is a 10 to 1 adhesive that requires a mixing tip with more mixing chambers to ensure proper mixing before use. These mixing tips minimize waste compared with traditional 6" mixing tips. This package contains 10 mixing tips.Features:10 to 1 adhesive

Read more less

Acrylic AdhesiveCAN NOT SHIP AIR,UPS GROUND ONLYAT-2010 is our biggest seller and is a unique adhesive. It has high viscosity and will hold smaller parts without sagging. AT-2010 cures in 5 - 6 minutes, has a 4 minute working time and develops working strength in 15 -20 minutes. This makes AT-2010 the ideal adhesive for applications which require an immediate high strength bond. AT-2010 has a 6 month shelf life when stored at 72 degrees. We recommend that where ever possible this adhesive be refrigerated. Packaged in a 50ml cartridge and can be mixed by hand or by using our AT-300 gun and mixing tips. The 50ml cartridge will bond 150 - 200 parts.** AT 850 Mixing Tips sku 56273 required ** Brochure (pdf)

Read more less

Black Nylon Wire Tie MountThe AT-3 tie mount is smaller for panel and other small space applications. This part is molded in black nylon and is sized for a #3 wire tie with a maximum width of .20". Average pull strength is about 50 lbs. The square base measures .44" wide. Use this smaller wire tie for runs with only a few wires or where space prevents use of our larger tie mounts. Excellent for mounting compass wires on center console boats and for overhead panel runs.

Read more less