Electrical

SmartSolar MPPT Charge Controller - 100V - 50AMPFeatures: Bluetooth Smart built-in The wireless solution to set-up, monitor, update and synchronise SmartSolar Charge Controllers.  VE.Direct For a wired data connection to a Color Control GX, other GX products, PC or other devices  Ultra-fast Maximum Power Point Tracking (MPPT) Especially in case of a clouded sky, when light intensity is changing continuously, an ultra-fast MPPT controller will improve energy harvest by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers.  Load output Over-discharge of the battery can be prevented by connecting all loads to the load output. The load output will disconnect the load when the battery has been discharged to a pre-set voltage (48V model: interface with a relay). Alternatively, an intelligent battery management algorithm can be chosen: see Battery Life. The load output is short circuit proof.  Battery Life: intelligent battery management When a solar charge controller is not able to recharge the battery to its full capacity within one day, the result is often that the battery will continually be cycled between a ‘partially charged’ state and the ‘end of discharge’ state. This mode of operation (no regular full recharge) will destroy a lead-acid battery within weeks or months. The Battery Life algorithm will monitor the state of charge of the battery and, if needed, day by day slightly increase the load disconnect level (i.e. disconnect the load earlier) until the harvested solar energy is sufficient to recharge the battery to nearly the full 100%. From that point onwards, the load disconnect level will be modulated so that a nearly 100% recharge is achieved about once every week.  Programmable battery charge algorithm See the software section on our website for details  Day/night timing and light dimming option See the software section on our website for details  Internal temperature sensor Compensates absorption and float charge voltage for temperature.  Optional external battery voltage and temperature sensing via Bluetooth A Smart Battery Sense or a BMV-712 Smart Battery Monitor can be used to communicate battery voltage and temperature to one or more SmartSolar Charge Controllers Warranty InfoWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Specifications: Charger Input - Voltage: 18-100v Charger Output - Amps: 50a Charger Output Voltage: 12v/24v Charging Banks: 1 Portable: No Box Dimensions: 4"H x 6"W x 8"L WT: 3.95 lbs UPC: 8719076040194 Quick Guide (pdf)Brochure (pdf)

Read more less

5022 Panel Mount AGC/MDL Fuse Holder Replacement CapReplaces cap for 5021 Specifications: Fuse Type: AGC/MDL Type: Fuse Holders Box Dimensions: 1"H x 2"W x 4"L WT: 0.05 lbs UPC: 632085050221

Read more less

19mm Push Button Switch - Off/(On) Momentary Contact - Blue/Red LED - 1' LeadThis stainless-steel plated metal button can transform any dash by adding a touch of modern flair. This button has an “Off/(On)" momentary contact.The body design combined with the included gasket gives this button switch a waterproof rating of IP69K. At night, every switch is backlit with blue LED light for unparalleled visibility. That light changes to red to let users know that the function is on without question.Features:1 ft. leadSpecifications: Function: Off-(On) (momentary contact) Off/On: Blue/red Rear Mark Page: Green dot Switch Rating: 15A/12 – 24VDC   Material: Stainless steel Mechanical Life: 50,000 cycles     Electrical Life: 10,000 cycles Installation:Drill a 19mm hole into any material up to 6mm thick. Connect the 3 contacts for the button (color-coded for safety and convenience). Lastly, connect the 2 contacts for the LED. Specifications: Action: OFF/(ON) Color: Blue/Red Box Dimensions: 1"H x 1"W x 1"L WT: 0.21 lbs Quick Guide (pdf)Brochure (pdf)

Read more less

Original Equipment Quality Replacement Solenoid for BRP-OMC & Evinrude E-TECReplacement solenoid that will fit BRP-OMC, EVINRUDE E-TEC, 2010-UP 15 HP-300 HP.Replaces:BRP-OMC 587020*ARCO Assurance 12-month part and labor warranty protectionThis product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Read more less

MK-315D 3 Bank x 5 AmpsON-BOARD MARINE BATTERY CHARGERSReengineered with a microprocessor-based design, digital on-board chargers protect your battery, charge faster, and help you stay on the water longer.DIGITALLY CONTROLLEDWe set out to build a smarter charger, and the result is the ingenious microprocessor-based design of onboard units. By monitoring factors like temperature and state of charge, they deliver a faster, more regulated, precise charge so you can stay on the water longer, without worrying about your batteries.PROTECTS BATTERIESOn-board chargers feature Multi-Stage Charging and Automatic Temperature Compensation for more precise charges that won't damage your battery. And its automatic shut-off feature extends battery life by shutting down when charging is complete. So your battery and your day on the water will always last longer.TWO TIMES FASTER CHARGINGIn high temperatures, on-board chargers juice up your batteries up to twice as fast. Thanks to a digital design that monitors everything from temperature to state of charge, on-board chargers get the job done.ENHANCED STATUS CODESComprehensive readings on chargers inform you of the charge stage, maintenance mode status, any error notifications, and full charge.Features: Waterproof, shock- and vibration-resistant aluminum construction Saltwater tested and fully corrosion-resistant Short circuit, reverse polarity, arc, and ignition protected For use with 12V/6 cell batteries that are flooded/wet cell, maintenance-free, or starved electrolyte (AGM) only FCC compliant UL listed to marine standard 1236 Length - 12-1/2" Width - 7-1/2" Height - 4" Weight - 14lbs WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Charger Output - Amps: 15a Charging Banks: 3 Portable: No Charger Input - Voltage: 120v Charger Output Voltage: 12/24/36v Box Dimensions: 7"H x 8"W x 16"L WT: 15.6 lbs UPC: 029402034796 Owner's Manual (pdf)Brochure (pdf)

Read more less

15A to 50A 125/250V Pigtail AdapterAllows connection of 50A 125/250V inlets to 15A 125V cords.Features: LED Power Indicator Ergonomic design for easier gripping Fully molded with a sealing collar for use in wet locations 15A 125V output, for use with 120V devices WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Type: Pigtail Adapter Box Dimensions: 3"H x 7"W x 12"L WT: 2 lbs UPC: 093344062131

Read more less

Flip Pro Multi - Dual USB-C & 12V Power SocketCombining the features of the high-power Flip Pro Max and 12V Power Sockets into a beautiful multi-power solution.When not in use, the spring-loaded caps remain tightly closed, protecting the ports from the elements.Universal: Universal fit for any USB-C connectors Fast charge (60W max) up to 2 devices at a time Marine Ready: IPX4 waterproof with the cover closed UV resistant 316 stainless steel hinge and spring Electrical Information: 120 -150W max power (12V system only) Input voltage: 10-30V DC (12/24V System) Input current Max: 6A (10A fuse recommended) Key Information: To maximize charge performance, use the cable supplied with your tablet, phone, etc. (C to C, or C-lightning) Phones charge at the same speed on either a 12 or 24V system, but a 24V system must be used to get the full 60W output suitable for laptops Quick Guide (pdf)

Read more less

LED Battery TesterSpecifically for all 12 Volt DC batteries.

Read more less

Orion-Tr Smart 48/12-30A (360W) Isolated DC-DC Charger The Orion-Tr Smart DC-DC charger is a professional DC to DC adaptive 3-stage charger with built-in Bluetooth.For use in dual battery systems in vehicles or on boats where the (smart) alternator and the start battery are used to charge the service battery. The unit can be monitored and programmed via Bluetooth and can be remotely controlled via a remote on/off switch and has an engine running detection mechanism.The Orion-Tr Smart charger can be used in 48V systems and is suitable for both lead acid and lithium batteries. Unlimited multiple units can be connected in parallel to increase output power.Suitable for high temperatures up to 55°C with a full rated output up to 40°C.Bluetooth Smart enabled Any Bluetooth-enabled smartphone, tablet, or other device can be used to monitor, change settings, and update the charger when new software features become available. Instant Readout: The VictronConnect App can display key data, including warnings and alarms, on the Device list page without the need to connect to the product. Fully programmable Battery charge algorithm (configurable) or fixed output. Smart alternator compatibility: engine running detection mechanism. Adaptive 3-stage charge algorithm: bulk – absorption – float For lead acid batteries, it is important that during shallow discharges the absorption time is kept short to prevent overcharging of the battery. After a deep discharge, the absorption time is automatically increased to make sure that the battery is completely recharged. For lithium batteries absorption time is fixed, default 2 hours. Alternatively, a fixed output voltage can be chosen. Suitable for use in vehicles with a smart alternator (Euro 5 and Euro 6 engines)The built-in engine shutdown detection will stop the converter when the engine is not running. This prevents unwanted discharge of the starter battery.Remote on/offA remote on/off switch or relay contact can be connected to a two-pole connector. Alternatively, the H terminal (right) of the two-pole connector can be switched to battery plus, or the L terminal (left) of the two-pole connector can be switched to battery minus (or the chassis of a vehicle, for example).All models are short circuit proof and can be paralleled to increase output currentAn unlimited number of units can be connected in parallel.High temperature protectedThe output current will reduce at high ambient temperatures.IP43 protectionWhen installed with the screw terminals oriented downward.Screw terminalsNo special tools are needed for installation.Input fuse (not replaceable)Please contact your dealer for any returns, repairs or support issues related to this product. Brochure (pdf)

Read more less

SmartShunt 300A IP65 Bluetooth Battery MonitorThe SmartShunt is an all-in-one battery monitor, only without a display. Your phone acts as a display. The SmartShunt connects via Bluetooth to the VictronConnect app on your phone (or tablet) and you can conveniently read out all monitored battery parameters, like state of charge, time to go, historical information, and much more.Alternatively, the SmartShunt can be connected and read by a GX device. The connection to the SmartShunt is made via a VE direct cable.The SmartShunt is a good alternative to a BMV battery monitor, especially for systems where battery monitoring is needed but less wiring and clutter are desired. It is equipped with Bluetooth, a VE.Direct port, and a connection that can be used for monitoring a second battery, midpoint monitoring, or a temperature sensor.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)Owner's Manual (pdf)Brochure (pdf)

Read more less

Energy Meter VM-3P75CT Single + 3-PhaseThe Victron VM-3P75CT energy meter is a standard device to measure the power and energy of single- and three-phase applications and calculates each phase's power values and broadcasts this over VE.Can or Ethernet with a high rate.  It has built-in Ethernet and VE.Can ports for connecting to a GX device and the split-core current transformers enable easy and quick installation without modifying existing wiring.The energy meter works out of the box (the firmware may need to be updated; details can be found in the Firmware Updates chapter) as a grid meter for systems with a MultiPlus and Quattro. Configuration (via VictronConnect) is only required for changing the role and manual IP configuration rather than the default DHCP.  Its data is displayed on a GX device such as the Cerbo GX or Ekrano GX, as well as in VictronConnect and the VRM Portal.Specifications: Voltage connection: Direct Input voltage range L-N: 85 to 265VAC Input voltage range L-L;150 to 460VAC Frequency: 50/60Hz Current connection: Via current transformers (included - wire length 640mm (25.2in) Rated current: 75A VE.Can communication port: Two RJ45 connectors (VE.Can terminators included) Ethernet communication port: One RJ45 connector, Modbus UDP Refresh rate: 100ms Type: Self-power supply via L1-N Switch or circuit breaker: Required as means of a disconnecting device - not included External fuse [1]: Required in the neutral conductor - 500mA, not included Consumption: 1.45W / 3.1VA Frequency: 50/60Hz Material & Color: Polycarbonate, blue (RAL5012) Voltage connection: Screw terminals 0.25 - 1.5mm2 (24 - 16AWG) Current transformer connection: Pluggable screw terminals (included) Protection category: IP20 Weight: 370g (including packaging) Dimensions: 90 x 71 x 59mm (3.5 x 2.8 x 2.3in) Indoor/outdoor usage: Indoor only Operating temperature: From -10 to +55 °C Storage temperature: From -20 to +70 °C Relative humidity: < 90% non-condensing Altitude: 2000m (6562ft) Mains supply voltage fluctuations: ±0.1Vin Overvoltage category: Cat. III Pollution degree: 2 What's In The Box? Victron VM-3P75CT with 3 input terminal blocks 3x Split-core current transformer, wired ready for connection Wire length: 640mm (25.3") VE.Can terminators (2-pieces) Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)

Read more less

MareLube TEF45 Max PTFE Heavy Load Lubricant - 16 oz.Marelube is Forespar's new family of three specifically formulated synthetic lubricants designed for various uses around your boat. Each contains PTFE and they work equally well in fresh or salt water. Marelube TEF 45 is a highly water-resistant synthetic lubricanat grease containing 45% PTFE. This is the highest percentage PTFE available, which makes TEF 45 perfect for heavy loads and bi-metal anti-corrosion applications like turnbuckles, spar fittings and motor lower units. TEF 45 also works well at protecting against rust corrosion and anti-seize applications. Features: Max PTFE Heavy Load Formulation Highly Water Resistant Bi-metal Corrosion Protection Specifications: Type: Grease Box Dimensions: 4"H x 4"W x 4"L WT: 1.1 lbs UPC: 028026190949

Read more less