Electrical - Battery Chargers

Orion-Tr Smart 48/48-8A (380W) Isolated DC-DC Charger The Orion-Tr Smart DC-DC charger is a professional DC to DC adaptive 3-stage charger with built-in Bluetooth.For use in dual battery systems in vehicles or on boats where the (smart) alternator and the start battery are used to charge the service battery. The unit can be monitored and programmed via Bluetooth and can be remotely controlled via a remote on/off switch and has an engine running detection mechanism.The Orion-Tr Smart charger can be used in 12V or 24V systems and is suitable for both lead acid and lithium batteries. Models are available up to 400W and unlimited multiple units can be connected in parallel to increase output power.Suitable for high temperatures up to 55°C with a full rated output up to 40°C.Bluetooth Smart enabled Any Bluetooth-enabled smartphone, tablet, or other device can be used to monitor, change settings, and update the charger when new software features become available. Instant Readout: The VictronConnect App can display key data, including warnings and alarms, on the Device list page without the need to connect to the product. Fully programmable Battery charge algorithm (configurable) or fixed output. Smart alternator compatibility: engine running detection mechanism. Adaptive 3-stage charge algorithm: bulk – absorption – float For lead acid batteries, it is important that during shallow discharges the absorption time is kept short to prevent overcharging of the battery. After a deep discharge, the absorption time is automatically increased to make sure that the battery is completely recharged. For lithium batteries absorption time is fixed, default 2 hours. Alternatively, a fixed output voltage can be chosen. Suitable for use in vehicles with a smart alternator (Euro 5 and Euro 6 engines)The built-in engine shutdown detection will stop the converter when the engine is not running. This prevents unwanted discharge of the starter battery.Remote on/offA remote on/off switch or relay contact can be connected to a two-pole connector. Alternatively, the H terminal (right) of the two-pole connector can be switched to battery plus, or the L terminal (left) of the two-pole connector can be switched to battery minus (or the chassis of a vehicle, for example).All models are short circuit proof and can be paralleled to increase output currentAn unlimited number of units can be connected in parallel.High temperature protectedThe output current will reduce at high ambient temperatures.IP43 protectionWhen installed with the screw terminals oriented downward.Screw terminalsNo special tools are needed for installation.Input fuse (not replaceable)Please contact your dealer for any returns, repairs or support issues related to this product. Brochure (pdf)

Read more less

SmartSolar MPPT 450/100-MC4 VE.Can VE.Direct 450/100The SmartSolar MPPT RS solar charge controllers are Victron's solution for systems with large series connected PV arrays charging 48 V DC battery banks. This product is perfect for large off-grid, and grid-connected battery systems.In a 5.76kW and 11.52kW model, features include a wide 65-450 VDC operating solar voltage input, independent tracking inputs, full connectivity, isolated PV connections, a display screen, fully programmable battery charging parameters, and active cooling. The new metal case design and fully covered electrical connections improve safety and modernize the presentation in line with the latest suite of Victron products.MPPT: Ultra Fast Maximum Power Point TrackingThe SmartSolar RS solar charge controller connects to a PV array of between 65 and 450 Volt Voc and will efficiently charge your 48V battery bank with either 100A or 200A.The charge settings are fully programmable and can be set up for different battery chemistries, like lead-acid, lithium and more.Setup & monitor with VictronConnectThe SmartSolar RS charge controller can be remotely controlled and configured over Bluetooth via the VictronConnect app. This allows device set-up, management, and at-a-glance information, such as battery voltage and current, PV voltage and current, historical data and trends.Daisy Chain Additional UnitsThe SmartSolar RS charge controller is equipped with VE.Can bus ports. This allows for communication with additional SmartSolar RS & VE.Can MPPT units. The additional units are simply “daisy chained” to each other with an RJ45 cable.When connected to each other, all individual charge controllers, will synchronise their charge stages. They can also send their data, via the same cable, for monitoring to a GX device (such as the Cerbo GX).Remote Monitoring and ControlIf the GX device is connected to the internet, the Victron Remote Management Portal (VRM) provides access to the full power of your SmartSolar RS charge controllers.If your installation is connected to a GX device and the internet, Victron Remote Management Portal (VRM) provides access to the full power of your MPPT, anytime, anywhere; for free. For remote installations - even when there is no internet connection nearby - you may be able to monitor your MPPT by connecting the GlobalLink 520.SmartSolar DisplayThe SmartSolar RS charge controller is equipped with a display on the front panel. The display reads battery volts, charge current and voltages from both array’s individually including instantaneous and total figures and unit status including any possible error codes.I/O ConnectionsThe SmartSolar RS charge controller is equipped with a programmable relay and options for remote temperature and voltage sensing. The remote input can accept the Victron smallBMS and other types of BMS with allow-to-charge signals.  VictronConnectVictronConnect lets you get live status information and configure any Victron products which either have Bluetooth built-in, or are connected to a VE.Direct Bluetooth Smart Dongle.Please contact your dealer for any returns, repairs or support issues related to this product. Owner's Manual (pdf)Brochure (pdf)

Read more less

Convenient Dual Battery Bank ChargingXantrex digital echocharge (part#82-0123-01) is designed to charge auxiliary or starting batteries from an inverter/charger or other charging source with limited voltage drop. The Xantrex echocharge detects when the house battery bank is being charged and directs a portion of the charge current to auxiliary or starting batteries. The maximum charger current offered by echocharge is limited to 15 amps.Product Features 15 A maximum charge current Automatically adjusts for 12 or 24 volt battery banks (both battery banks must be the same DC voltage and battery type) Automatically switches on/off without affecting the in-house battery bank or over-charging Utilizes excess current from the primary charging source Built-in thermal and over-current circuits Reverse polarity protection Easy three wire installation WARNING: This product can expose you to chemicals including Diisononyl Phthalate (DINP) which is known to the State of California to cause cancer, and Di-isodecyl Phthalate (DIDP) which is known to the State of California to cause reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Charger Output - Amps: 15a Charging Banks: 1 Portable: No Charger Input - Voltage: 120v Charger Output Voltage: 12/24v Box Dimensions: 3"H x 7"W x 10"L WT: 1.2 lbs UPC: 647912105722 Quick Guide (pdf)Owner's Manual (pdf)

Read more less

Blue Smart IP65 Charger 12/5(1) 120V The Blue Smart IP65 Charger is a professional battery charger with built-in Bluetooth. The Blue Smart IP65 Charger can be used on devices in your workshop and on motor vehicles, such as (classic) cars; motorbikes; boats, and camper-vans.The battery is charged, smartly... to perfect conditionThe seven-step charging algorithm gets the best out of your battery. The charger gives the battery the power it needs, maintains its health, ensures better performance... and longer life.Recovery of deeply-discharged 'dead' batteriesUnlike other brands, the Blue Smart IP65 Charger will attempt to recharge a deeply discharged battery by force-feeding it with a low current. Normal charging will then be resumed as soon as there is sufficient voltage across the battery terminals.Connect the battery with easeThe charger comes with both crocodile clips and M8 eyelets - making it easy to connect to the battery. If you wish, you can leave it permanently connected.Check the status of your battery remotelyThe Blue Smart IP65 is equipped with built-in Bluetooth, so the status of the charger and the battery can be checked on a smartphone, tablet, or laptop. All settings of the charger can be configured with the VictronConnect app.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)

Read more less

Blue Smart IP22 12VDC 30A 1 Bank 120V Charger - Dry MountThe Blue Smart IP22 Charger is the professional battery charger with built-in bluetooth. The Blue Smart IP22 Charger can be used on devices in your workshop and on motor vehicles, such as (classic) cars; motorbikes; boats and camper-vans. Bluetooth SmartThe Blue Smart IP22 Charger is the wireless solution to monitor voltage and current, to change settings and to update the charger when new features become available.High efficiencyWith up to 94% efficiency, these chargers generate up to four times less heat when compared to the industry standard. And once the battery is fully charged, power consumption reduces to 0,5 Watt, some five to ten times better than the industry standard.Adaptive 6-stage charge algorithm: test - bulk – absorption - recondition – float – storageThe Blue Smart Charger features a microprocessor-controlled ‘adaptive’ battery management. The adaptive feature will automatically optimize the charging process relative to the way the battery is being used.Storage Mode: less maintenance and aging when the battery is not in useThe storage mode kicks in whenever the battery has not been subjected to discharge during 24 hours. In the storage mode float voltage is reduced to 2,2V/cell (13,2V for a 12V battery) to minimize gassing and corrosion of the positive plates. Once a week the voltage is raised back to the absorption level to ‘equalize’ the battery. This feature prevents stratification of the electrolyte and sulfation, a major cause of early battery failure.Also charges Li-ion batteriesLi-ion batteries are charged with a simple bulk – absorption – float algorithm.Fully discharged battery recovery functionWill initiate charging even if the battery has been discharged to zero volts. Will reconnect to a fully discharged Li-ion battery with internal disconnect function.NIGHT and LOW settingWhen in NIGHT or LOW mode, the output current is reduced to max. 50% of the nominal output and the charger will be totally noiseless. The NIGHT mode automatically ends after 8 hours. The LOW mode can be ended manually.Protected against overheatingOutput current will reduce as the temperature increases up to 50°C, but the Blue Smart Charger will not fail.Eleven LEDs for status indicationCharge algorithm: TEST / BULK / ABSORPTION / RECONDITION / FLOAT / STORAGE / READY. MODE button to set: NORMAL (14,4V) / HIGH (14,7V) / RECONDITION / LI-ION.Please contact your dealer for any returns, repairs or support issues related to this product. Specifications: Charger Output - Amps: 30a Charger Input - Voltage: 120v Portable: No Charging Banks: 1 Charger Output Voltage: 12v Box Dimensions: 3"H x 7"W x 11"L WT: 3.25 lbs UPC: 8719076052395 Quick Guide (pdf)Owner's Manual (pdf)Brochure (pdf)

Read more less

Premium Series Dolphin Battery Charger - 12V, 60A, 110/220VAC - 3 OutputsThe Premium range of chargers is perfect for most of today’s battery technologies, with a load capacity of up to 400 amps at 12V. These compact chargers are ideally suited to recharging batteries in light vehicles, ambulances, repair vehicles, and motorhomes. The Premium charger is perfect for workshops, pleasure boats, computer cabinets, and starter batteries for gen-sets.The robust compact housing is lighter and easier to install than ever thanks to better mounting design and electrical speed connections. Outstanding features include the latest battery charging technology and a new charging program for lithium-ion-iron-phosphate batteries. These chargers come in a nice package, making them ideal for retailers.Features: 12V, 60A Digital management with up-to-date RISC micro-controller 4 charging programs, including one for Lithium-Ion-Iron-Phosphate with integrated BMS. Charging program selection by internal dip switch. Automatic weekly equalization for all charging programs  Thanks to the Winsta (Wago) and Phoenix contact connectors, wiring, and connections are easy and user-friendly. 3 completely isolated battery outputs. Manual Night Mode (Silent – fan turned off) by push-button is included with 12V-40A and 24V-20A Automatic 115/230V switch-over Touchview controller connection  Specifications: Charger Input - Voltage: 110/220v Charger Output - Amps: 60a Charger Output Voltage: 12v Charging Banks: 3 Portable: No Box Dimensions: 6"H x 11"W x 13"L WT: 7.5 lbs UPC: 786142990507 Owner's Manual (pdf)

Read more less

ProMar1 DS Digital - 15 Amp - 3 Bank ChargerProMar1 DS Generation 3 reflects a new outward design taken to the next level in performance with its all Digital Charging Technology. Fully Automatic with a 4-Stage Digital Charging algorithm proven to extend battery life. Sequential modes of Analyzing, Charging, Conditioning and a built-in Auto Maintain mode, safe for short and long term storage periods ensures your batteries are fully charged and maintained.Features: Fully Automatic 4-Stage Charging Dual Mode Charge Status Indicator Battery & Wiring Fault Detection Rugged Shockproof Construction Auto Maintain/Energy Saver Mode Extends Battery Life Sage for Long and Short Term Storage Pre-Wired with Waterproof Inline DC Fuses and Nickel Plated Copper Ring Terminals Built-in Safety Quiet EMI Design Meets US FCC Emissions Requirements WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Charger Output Voltage: 12/24/36v Charger Output - Amps: 15a Charger Input - Voltage: 120v Portable: No Charging Banks: 3 Box Dimensions: 5"H x 9"W x 12"L WT: 12.1 lbs UPC: 031669315150

Read more less

Centaur Charger - 12 VDC - 100AMP - 3-Bank - 120-240 VACFeatures: Quality without compromise -  Aluminium epoxy powder coated cases with drip shield and stainless steel fixings withstand the rigors of an adverse environment: heat, humidity and salt air. Circuit boards are protected with an acrylic coating for maximum corrosion resistance. Temperature sensors ensure that power components will always operate within specified limits, if needed by automatic reduction of output current under extreme environmental conditions. Universal 90-265V AC input voltage range and also suitable for DC supply (AC-DC and DC-DC operation) All models will operate without any adjustment needed over a 90 to 265 Volt input voltage range, whether 50 Hz or 60 Hz.  The chargers also accept a 90-400 V DC supply.  Three outputs that each can supply the full output current Three isolated outputs to simultaneously charge 3 battery banks Each output is capable to supply the full rated current.  Three-stage charging, with temperature compensation The Centaur charges at bulk rate until the output has reduced to 70% of the rated Amps, at which a 4 hour timer begins. After the timed period the charger switches to float rate. An internal temperature sensor is used to compensate the charge voltage with – 2 mV/ºC (– 1 mV/ºF) per cell. A DIP switch is available to select the optimum charge/float voltages for Flooded Lead-acid, Gel or AGM batteries Warranty InfoWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Specifications: Charging Banks: 3 Portable: No Charger Output Voltage: 12v Charger Output - Amps: 100a Charger Input - Voltage: 120/240v Box Dimensions: 9"H x 14"W x 25"L WT: 24.25 lbs UPC: 8719076021537 Quick Guide (pdf)Owner's Manual (pdf)Brochure (pdf)

Read more less

Orion-TR Smart 12/24-15A (360W) Isolated DC-DC Charger or Power SupplyThe Orion-Tr Smart isolated DC-DC charger serves as a DC-DC battery charger or a power supply (also designed for use as a constant voltage source), offering a wide input and output voltage range. This is especially significant in the case of vehicles with a Euro 5 or Euro 6 smart alternator, which often supplies too low charging voltage even when the engine is running or when extended cable lengths, as is often the case in boats and RVs, lead to voltage drops. In such scenarios, precise and controlled charging is imperative to fully charge the service battery while protecting the starter/input battery from discharge.Bluetooth Smart Enabled Any Bluetooth-enabled smartphone, tablet, or other device can be used to monitor, change settings, and update the charger when new software features become available Instant Readout: The VictronConnect App can display key data, including warnings and alarms, on the device list page without the need to connect to the product Fully programmable Battery charge algorithm (configurable) or fixed output.  Smart Alternator Compatibility: engine running detection mechanism Adaptive 3-Stage Charge Algorithm: Bulk – Absorption – Float For lead-acid batteries, it is important that during shallow discharges the absorption time is kept short to prevent overcharging of the battery. After a deep discharge, the absorption time is automatically increased to make sure that the battery is completely recharged For lithium batteries, the absorption time is fixed; the default is 2 hours Alternatively, a fixed output voltage can be chosen Suitable for Use in Vehicles with a Smart Alternator (Euro 5 and Euro 6 Engines)The built-in engine shutdown detection will stop the converter when the engine is not running. This prevents unwanted discharge of the starter battery (see manual for details).Remote On/OffA remote on/off switch or relay contact can be connected to a two-pole connector. Alternatively, the H terminal (right) of the two-pole connector can be switched to battery plus, or the L terminal (left) of the two-pole connector can be switched to battery minus (or the chassis of a vehicle, for example).All Models Are Short Circuit Proof and Can Be Paralleled to Increase Output CurrentAn unlimited number of units can be connected in parallel.High Temperature ProtectedThe output current will reduce at high ambient temperatures.IP43 ProtectionWhen installed with the screw terminals oriented downward.Screw TerminalsNo special tools are needed for installation. Input fuse (not replaceable) *Input fuse (not replaceable) Specifications: Input Voltage Range: 10-17 V Under Voltage Shut Down: 7 V Under Voltage Restart: 7.5 V Nominal Output Voltage: 24.2 V Output Voltage Adjust Range: 20-36 V Output Voltage Tolerance: +/- 0,2 V Output Noise: 2 mV rms Cont. Output Current at Nominal Output Voltage and 40 Degrees C: 15 A Maximum Output Current (10 S) at Nominal Output Voltage minus 20%: 25 A Short Circuit Output Current: 40 A Cont. Output Power at 25 Degrees C: 430 W Cont. Output Power at 40 Degrees C: 360 W Efficiency: 88 % No Load Input Current (2): < 100 mA  Standby Current: Less than 1A Can Be Used as Power Supply: Yes, output voltage can be set with Bluetooth  Galvanic Isolation: 200 VDC between input, output, and case  Operating Temperature Range -20 to +55 °C (derate 3 % per °C above 40 °C)  Humidity: Max. 95 % non-condensing  DC Connection: Screw terminals  Maximum Cable Cross-Section: 16 mm²  AWG6  Weight: 1,8 kg (3 lb)  Dimensions (H x W x D):130 x 186 x 70 mm  (5.1 x 7.3 x 2.8 inch)  Protection Category IP43 (electronic components), IP22 (connection area)  Safety Standards: EN 60950 Emission/Immunity Standards: EN 61000-6-3, EN 55014-1 / EN 61000-6-2, EN 61000-6-1, EN 55014-2 Automotive Directive Standards: ECE R10-5 WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Specifications: Portable: No Charging Banks: 1 Charger Output Voltage: 24v Charger Output - Amps: 15a Charger Input - Voltage: 12v Box Dimensions: 4"H x 5"W x 8"L WT: 4.4 lbs UPC: 8719076047704 Quick Guide (pdf)Owner's Manual (pdf)Brochure (pdf)

Read more less

PRO Evo3 - 24V - 40AThis range of Marine Battery Chargers is the result of the latest technological advancements in the world of power electronics. By comparison to the Dolphin Pro Chargers, an additional DC output has been added while reducing the overall dimensions by 16% (12v/90a, 24v/40a, 24v/60a) and 30% (24v/100a). They are more compact and 30-60% lighter (9 lbs.) offering the highest power-to-space ratio on the market! With 4 independent isolated DC outputs and NMEA 2000 communication, the Dolphin PRO Evo3 meets the demands of today’s leading boat builders and modern electrical systems.Features: Ultra-compact and lightweight - Thanks to the new electronics this new generation of product is 30 to 60% lighter than the previous one. The weight of the 24-volt 100-amp unit is just under 9 Lbs. 4 Independent isolated outputs - All PRO EVO3 offer 4 independent isolated DC outputs. It allows to simplification of the charging system consisting of several battery banks. NMEA 2000 - NMEA 2000 plug-and-play communication skills. All PRO EVO3 chargers feature CAN communication ports including certified N2K port with latest PGEN. High-Efficiency DSP technology - PRO EVO3 Chargers deliver full power even at very high temperatures (up to 50°C/122°F). This "no derating" feature is unique on the market. Selectable Battery Chemistries - 8 Selectable charging profiles including Lead Acid, Gel, AMG, and Lithium-Ion batteries with temperature compensation. Ignition Protected - PRO EVO3 12.90 is now ISO 8846 and SAE J1171 certified. Brochure (pdf)

Read more less

ChargeMaster Plus 24V, 60A, 3-Bank, NMEA2000 - CZoneChargeMaster Plus 24/60-3 CZoneAll-in-one solution for faster and safer chargingChargeMaster Plus is the next generation of battery chargers that integrates multiple functions into one single device. Replacing auxiliary chargers, battery isolators and VSR, ChargeMaster Plus reduces system complexity and cost. Designed for versatility, it charges virtually any combination of two or three batteries in a fast and safe way and works anywhere in the world.With the new Battery’s Best Friend architecture, ChargeMaster Plus is capable of charging a multitude of battery chemistries, sizes and voltages. All batteries are charged with the fast and safe 3-step+ charge method. Other unique features are: Revival mode: automatically revives even fully depleted batteries. Multi voltage: charge 12 V starter battery in a 24 V system, without additional components. Priority Charge: redirect available power to the lowest battery, for faster charging. Smart Input: charge all three batteries from one single alternator for continuous charging on the go. Global ChargingThe ChargeMaster Plus handles worldwide AC voltages and frequencies. Resisting large voltage fluctuations and high temperatures, it keeps working in harsh environments. For marine and mobile markets, the ChargeMaster Plus is CE, ABYC, UL, SAE, CEC/DOE and RCM/C-Tick compliant.System SimplicityNowadays, equipment must be self-explaining. The ChargeMaster Plus displays the charge phase of all outputs in an understandable way. Robust and ergonomic connections save installation time. An integrated VSR eliminates the need for additional components and ensures that the alternators energy is funnelled through to the batteries.Powerful Communications thanks to CZone integrationIn modern applications, all electrical components work together. The CAN-based MasterBus enables the ChargeMaster Plus to communicate with displays, shunts and power systems including communication standards like CZone®, NMEA 2000 and CANopen (through additional interfaces).Models with the addition CZone do not only support MasterBus, but also support CZone and NMEA 2000 communication, without the need of additional interfaces. This ChargeMasters Plus series can be configured via MasterBus or will accept a CZone configuration file just like any other CZone device. Other communication standards like ModBus, CANopen, LinBus, etc. are supported via additional interfaces.This wide range of communication interfaces makes the ChargeMaster Plus ideally suited for system integration. In addition, the ChargeMaster Plus can operate as a power supply for delicate communication equipment, or during the construction phase of a boat.Features: Multicharger with two outputs, one in/output, DC-DC converter, current limiter and VSR. Combine Lithium Ion, Gel or AGM, and large or small battery banks on a single battery charger. Charges multiple batteries while being underway. Extended specifications: offers 20 % more output at 14.4 V and 80 % charging power at 60 °C. Safe Charge: quickly recognize the State of Charge for extended battery life. Very wide operating range of 80-275 V AC, 35-70 Hz. Compact, easy to connect and quick to install WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Portable: No Charging Banks: 3 Charger Output Voltage: 24v Charger Output - Amps: 60a Charger Input - Voltage: 120/240v Box Dimensions: 7"H x 13"W x 18"L WT: 16.75 lbs UPC: 816882022524 Owner's Manual (pdf)

Read more less

Blue Smart IP65 Charger - 6V/12V - 1.1A - 120V - 1-15PThe Blue Smart IP65 Charger is the new professional battery charger with built-in Bluetooth. The Blue Smart IP65 Charger can be used on devices in the workshop and motor vehicles, such as (classic) cars; motorbikes; boats, and camper vans. The battery is charged, smartly... to the perfect conditionThe seven-step charging algorithm gets the best out of a battery. The charger gives the battery the power it needs, maintains its health, and ensures better performance... and longer life.Recovery of deeply-discharged 'dead' batteriesUnlike other brands, the Blue Smart IP65 Charger will attempt to recharge a deeply-discharged battery by force-feeding it with a low current. Regular charging will then be resumed as soon as sufficient voltage is across the battery terminals.Connect the battery with easeThe charger comes with both crocodile clips and M8 eyelets - making it easy to connect to the battery. If users wish, it can be left permanently connected.Check the status of your battery remotelyThe Blue Smart IP65 is equipped with built-in Bluetooth, so the status of the charger and the battery can be checked on a smartphone, tablet, or laptop. All settings of the charger can be configured with the VictronConnect app.Specifications: Input Voltage & Frequency Range: 100 - 250VAC | 45 - 65Hz  Efficiency: 82% Standby Power Consumption: <0,5 W  Minimum Battery Voltage: Starts charging from down to 0 V Charge voltage 'absorption': Normal: 7,2 V | 14,4 V / High: 7,35 V | 14,7 V / Li-ion: 7,1 V | 14,2 V Charge Voltage 'float': Normal: 6,9 V | 13,8 V / High: 6,9 V | 13,8 V / Li-ion: Disabled Charge Voltage 'storage': Normal: 6,6 V | 13,2 V / High: 6,6 V | 13,2 V / Li-ion: 6,75 V | 13,5 V Charge Current: 1.1 A  Low-Current Mode: 0,5A  Temperature Compensation (lead-acid batteries only): 8 mV/°C | 16 mV/°C  Power Supply Mode: Yes Back Current Drain: 0,1 Ah/month (140uA)  Protection: Reverse polarity, Output short circuit, Over-temperature Operating Temp. Range: -30 to +50°C (full rated output up to 30°C) Humidity (non-condensing): Max 95% Charge Algorithm: 7-stage adaptive Bluetooth: 4dBm, 2402–2480 MHz Enclosure Specifications: Battery-Connection: Black and red cable of 1,5 meter 230V AC connection: 1.5m cable with CEE 7/16 or AS/NZS 3112 plug Protection Category: IP65 (splash and dust proof) Weight: 0,4 kg Dimensions: 38 x 64 x 153 mm Standards: Safety: EN 60335-1, EN 60335-2-29 Emission; EN 55014-1, EN 61000-6-3, EN 61000-3-2 Immunity: EN 55014-2, EN 61000-6-1, EN 61000-6-2, EN 61000-3-3 Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)Owner's Manual (pdf)Brochure (pdf)

Read more less