Electrical - Battery Management

e-Series Dual Circuit Plus PN 5511e(1) 100A C-Series Flat Rocker Circuit Breaker(2) 15A Push Button Thermal Circuit Breakers Designed for twin engine configurations Provides 24 hour circuit protection Provides main DC circuit protection in addition to high ampere load protection Protects electronics from sags and spikes caused by engine cranking Allows emergency cross connect between isolated battery banks Isolates the Engine circuit from the House circuit Simplifies battery switch operation Allows independent battery discharge Addition of an Automatic Charging Relay automates charging both batteries Includes 4218 - Square Format Labels and 4140 - 24 Hour Round Labels WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Quick Guide (pdf)Owner's Manual (pdf)

Read more less

BlueSolar MPPT Charge Controller - 75V - 15AMPFeatures: Ultra-fast Maximum Power Point Tracking (MPPT) Especially in case of a clouded sky, when light intensity is changing continuously, an ultra-fast MPPT controller will improve energy harvest by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers.  Load output Over-discharge of the battery can be prevented by connecting all loads to the load output. The load output will disconnect the load when the battery has been discharged to a pre-set voltage. Alternatively, an intelligent battery management algorithm can be chosen: see Battery Life. The load output is short circuit proof. Some loads (especially inverters) can best be connected directly to the battery, and the inverter remote control connected to the load output. A special interface cable may be needed, please see the manual.  Battery Life: intelligent battery management When a solar charge controller is not able to recharge the battery to its full capacity within one day, the result is often that the battery will continually be cycled between a ‘partially charged’ state and the ‘end of discharge’ state. This mode of operation (no regular full recharge) will destroy a lead-acid battery within weeks or months. The Battery Life algorithm will monitor the state of charge of the battery and, if needed, day by day slightly increase the load disconnect level (i.e. disconnect the load earlier) until the harvested solar energy is sufficient to recharge the battery to nearly the full 100%. From that point onwards the load disconnect level will be modulated so that a nearly 100% recharge is achieved about once every week.  Programmable battery charge algorithm See the software section on our website for details  Day/night timing and light dimming option See the software section on our website for details  Programming, real-time data and history display options - Color Control GX or other GX devices: see the Venus documents on our website. - A smartphone or other Bluetooth-enabled device: VE.Direct Bluetooth Smart dongle needed Warranty InfoWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Specifications: Charger Input - Voltage: 18-75v Charger Output - Amps: 15a Charger Output Voltage: 12v/24v Charging Banks: 1 Portable: No Box Dimensions: 2"H x 6"W x 6"L WT: 1.3 lbs UPC: 8719076025320 Quick Guide (pdf)Brochure (pdf)

Read more less

Medium Duty Main Battery Disconnect SwitchesIgnition ProtectedFor use with 12, 24 and 32 volt marine electrical systemscapacity - rated 250 amps continuous,360 amps intermittent Medium Duty Main Battery Disconnect Switch w/ Key Lock Specifications: AFD: No Lockable: Yes Positions: 1 Continuous Amperage: 250a Box Dimensions: 3"H x 6"W x 8"L WT: 0.9 lbs UPC: 085226560446 Quick Guide (pdf)

Read more less

Distribution Cluster for Single Engine with Two Battery BanksThe 714-140A-DVSR uses a dual sensing DVSR (710-140A). This system ensures that you will always have a fully charged reserve battery. When the switch is in position one, battery one becomes the sensing battery for the VSR. Battery two, which is in isolation, is charged through the VSR when the engine is running to ensure that it is always fully charged. When the switch is in position two, battery two becomes the sensing battery and battery one is charged through the VSR. The fact that there is always a fully charged battery in reserve is a huge safety benefit.WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Lockable: No Positions: 3 Continuous Amperage: 140a Box Dimensions: 3"H x 4"W x 10"L WT: 1.06 lbs UPC: 843687005582

Read more less

GX LTE 4G-A Cellular Modem for GX Devices - North America OnlyThe GX LTE 4G is an accessory for GX devices. It is a cellular modem that supports 2G, 3G, and 4G technologies. It provides mobile internet for the system and a connection to the Victron Remote Management (VRM) portal.Built-in GPS ReceiverThe GX LTE 4G includes a built-in GPS receiver. When the optional active GPS antenna is installed, the system can be tracked as well as geo-fenced on the VRM Portal.The required accessory part number is GSM900200100 - Active GPS Antenna for GX GSM.GX CompatibilityThe GX LTE 4G can be used with any of the GX devices and requires Venus OS v2.60 or newer to be installed on the GX device.SIM CardIt requires a SIM card in the Mini-SIM format.When to Use a Mobile Router InsteadThe GX LTE 4G provides an internet connection for the GX device only. There is no option to share the internet with laptops, phones, or other devices. For installations where more devices need internet, such as a yacht or RV, consider installing a mobile router instead.Antennas and AccessoriesA small indoor LTE antenna is included. Optionally, Victron sells an outdoor LTE antenna, which increases the range.Part number GSM900100400 - Outdoor 4G GSM Antenna.Specifications: Region: For North America Used Module: SIMCom, SIM7600A Supported LTE Bands: 2, 4, 12 Supply Voltage Range: 8 - 70VDC Power Draw: 2.5W while 2G/3G/4G data transfer / <1.0W in idle mode / +0.4W if GPS is enabled Operating Temperature Range: -40 +50°C (-40 - 120°F) Power Cable (Included): 1.4m cable with inline fuse holder, terminal block, and 10mm ring terminals Inline Fuse (included): T3.15A250V Communication Specifications: USB Communication Port: Fixed 1.0m cable with USB-A connector (connects to the GX device) LTE Antenna Connector: Type SMA Female (optional 4G outdoor antenna GSM900100400) GPS Antenna Connector: Type SMA Female (optional GPS antenna GSM900200100) GNSS: GPS/Beidou/GLONASS/GALILEO/QZSS SIM Card: Regular Mini SIM (supports both 1.8V and 3V) Data Transmission (max. Download/Upload) LTE Cat-1: 10 Mbps / 5 Mbps Data Transmission (max. Download/Upload) 3G (HSPA+): 42 Mbps / 5.76 Mbps Data Transmission (max. Download/Upload) 2G (EDGE): 236.8 Kbps / 236.8 Kbps Data Transmission (max. Download/Upload) 2G (GPRS): 85.6 Kbps / 85.6 Kbps Status Indicator: Blue LED Installation & Dimensions: Dimensions (l x w x h): 106 × 42.5 × 22mm Weight: 0.08kg (0.177lbs) Wire Gauge (power cable): 0.5..1.5mm2 / AWG 28..16 or use supplied power cable Recommended Fuse Size: 500mA @ 12V / 250mA @ 24V / 100mA @ 48V or use supplied inline fuse In the Box: GX LTE 4G (with integrated USB cable) GSM 2G/3G/4G mini-rod antenna (for indoor use) DC power cable (with inline fuse and terminal block) Standrads: Safety: EN 60335-1 / EN 60335-2-29 / EN 62368-1 Emission / Immunity: ECE R10-5 QM: EN 9001:2015 Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)Owner's Manual (pdf)

Read more less

M8 Circular Connector 3-Pole BMS BTV Extension Cables - Pair - 2MFeatures: 2-meter cable Extends the data cables that run from a 12.8 Volt Lithium-Ion battery to the BMS Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)

Read more less

M8 Circular Connector 3-Pole BMS BTV Extension Cables - Pair - 3MFeatures: 3-meter cable Extends the data cables that run from a 12.8 Volt Lithium-Ion battery to the BMS Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)

Read more less

Pro Installer 400A EZ-Mount Battery Selector Switch (1-2-Both-Off)As easy as 1, 2, 3, these revolutionary battery switches allow you to wire from the front. Never has installation been so easy and cabling so accessible. With their shared interconnection height, EZ-Mount battery switches "cluster" directly with the Pro Installer Busbar Range, resulting in the fastest, most compact installations. Optimized cable access makes installation a breeze. Pro Installer switches set the new benchmark with outstanding ergonomics, intuitive look/feel, and are engineered from the finest materials to withstand the harsh marine environment. The outstanding performance and features of this powerful new generation battery switch appeal to both the installer and end user. All ratings, footprints and features of the EZ-Mount switch match the high quality of our standard switches. Tested to UL1107 ignition protection, CE Tinned copper 10mm (3/8") studs Stainless steel washers/nuts Fiber reinforced plastics 400A Continuous / 600A 5 mins Intermittent / 1500A 10 secs Cranking Waterproof to IP66 Same interconnection height as Pro Installer Removable knob allows isolation during servicing 3 removable sideplates for protection Industry standard 3.85" x 3.85" footprint SpecificationsMounting: Surface OnlyVoltage: 48v DC (for 12-48v systems)Rating: 400 Cont / 600 Inter / 1500 CrankDims: 3.85" x 3.85" x 3.62"Operation: 1-2-Both-OffStud: 3x 10 mm (3.8")WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: AFD: No Lockable: No Positions: 1-2-Both-Off Continuous Amperage: 400a Box Dimensions: 4"H x 7"W x 8"L WT: 1.2 lbs UPC: 843687007692 Owner's Manual (pdf)Brochure (pdf)

Read more less

Panel-Mounted Battery Mini Selector SwitchPanel-mounted switches are designed specifically for panel mount applications. This range gives a very compact, versatile solution. Compact, lightweight Countersunk recesses for surface mount application Standard 2-1/16" (52 mm) hole cut out (same as standard gauge hole) Inside: captive inserts for 3/16" (4.8 mm) nuts providing full access for cables with no restrictions Standard interchange label system Molded in high temperature, fiber reinforced plastics WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

1000A/50mV ShuntShunt 1000 Amp 50 mV - 1000A/50mV

Read more less

Lynx Smart BMS 500 M10 Battery Management SystemThe Lynx Smart BMS is a dedicated Battery Management System for Victron Lithium Smart Batteries. There are multiple BMS-es available for our Smart Lithium series of batteries, and the Lynx Smart is the most feature-rich and complete option. It is available in two versions: 500A and 1000A (both with M10 busbar connections).Features: Built-in 500A or 1000A contactor used as a fallback safety mechanism and also suitable as a remote controllable main system switch. Battery monitor, indicating state of charge percentage and more data. Pre-alarm signal: provide a warning before the system shuts down due to -for example- a low cell. Bluetooth for use with our VictronConnect app, for setup and monitoring, including Instant Readout - key data of the BMS at a glance. Local and remote monitoring using a Victron GX device, for example, the Cerbo GX or Ekrano GX. The Lynx Smart BMS is part of the modular Lynx Distribution system.VictronConnectVictronConnect lets you get live status information and configure any Victron products which either have Bluetooth built-in, or are connected to a VE.Direct Bluetooth Smart Dongle.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)Owner's Manual (pdf)Brochure (pdf)

Read more less

SmartSolar MPPT 450/100-MC4 VE.Can VE.Direct 450/100The SmartSolar MPPT RS solar charge controllers are Victron's solution for systems with large series connected PV arrays charging 48 V DC battery banks. This product is perfect for large off-grid, and grid-connected battery systems.In a 5.76kW and 11.52kW model, features include a wide 65-450 VDC operating solar voltage input, independent tracking inputs, full connectivity, isolated PV connections, a display screen, fully programmable battery charging parameters, and active cooling. The new metal case design and fully covered electrical connections improve safety and modernize the presentation in line with the latest suite of Victron products.MPPT: Ultra Fast Maximum Power Point TrackingThe SmartSolar RS solar charge controller connects to a PV array of between 65 and 450 Volt Voc and will efficiently charge your 48V battery bank with either 100A or 200A.The charge settings are fully programmable and can be set up for different battery chemistries, like lead-acid, lithium and more.Setup & monitor with VictronConnectThe SmartSolar RS charge controller can be remotely controlled and configured over Bluetooth via the VictronConnect app. This allows device set-up, management, and at-a-glance information, such as battery voltage and current, PV voltage and current, historical data and trends.Daisy Chain Additional UnitsThe SmartSolar RS charge controller is equipped with VE.Can bus ports. This allows for communication with additional SmartSolar RS & VE.Can MPPT units. The additional units are simply “daisy chained” to each other with an RJ45 cable.When connected to each other, all individual charge controllers, will synchronise their charge stages. They can also send their data, via the same cable, for monitoring to a GX device (such as the Cerbo GX).Remote Monitoring and ControlIf the GX device is connected to the internet, the Victron Remote Management Portal (VRM) provides access to the full power of your SmartSolar RS charge controllers.If your installation is connected to a GX device and the internet, Victron Remote Management Portal (VRM) provides access to the full power of your MPPT, anytime, anywhere; for free. For remote installations - even when there is no internet connection nearby - you may be able to monitor your MPPT by connecting the GlobalLink 520.SmartSolar DisplayThe SmartSolar RS charge controller is equipped with a display on the front panel. The display reads battery volts, charge current and voltages from both array’s individually including instantaneous and total figures and unit status including any possible error codes.I/O ConnectionsThe SmartSolar RS charge controller is equipped with a programmable relay and options for remote temperature and voltage sensing. The remote input can accept the Victron smallBMS and other types of BMS with allow-to-charge signals.  VictronConnectVictronConnect lets you get live status information and configure any Victron products which either have Bluetooth built-in, or are connected to a VE.Direct Bluetooth Smart Dongle.Please contact your dealer for any returns, repairs or support issues related to this product. Owner's Manual (pdf)Brochure (pdf)

Read more less