Electrical

SmartShunt 500AMP/50MV Bluetooth Smart Battery ShuntThe Smart Battery ShuntThe SmartShunt is an all in one battery monitor, only without a display. Your phone acts as the display. The SmartShunt connects via Bluetooth to the VictronConnect App on your phone (or tablet) and you can conveniently read out all monitored battery parameters, like state of charge, time to go, historical information and much more.Alternatively the SmartShunt can be connected and be read by a GX device. Connection to the SmartShunt is made via a VE.Direct cable.The SmartShunt is a good alternative for a BMV battery monitor, especially for systems where battery monitoring is needed but less wiring and clutter is wanted.The SmartShunt is equipped with Bluetooth, a VE.Direct port and a connection that can be used for: monitoring a second battery, midpoint monitoring or a temperature sensor.VictronConnectVictronConnect lets you get live status information and configure any Victron products which either have Bluetooth built-in, or are connected to a VE.Direct Bluetooth Smart Dongle.Warranty InfoWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)Owner's Manual (pdf)Brochure (pdf)

Read more less

ML-RBS Remote Battery Switch with Manual Control Auto-Release - 24V Manual override knob provides an added level of safety allowing control with or without power and offering LOCKED OFF capability for servicing LED output to remotely indicate switch state - requires optional LED 3/ 8"-16 tin-plated copper studs for maximum conductivity and corrosion resistance 7/ 8" (22mm) stud length accepts multiple cable terminals Label recesses for circuit identification Silver alloy contacts provide high reliability for switching live loads Auto Releasing ML-Series Remote Battery Switch with SPST Switching Provides 500A switching and features of current ML Remote Battery Switches, but can be controlled with SPST or SPDT switch for applications where a normally open relay is desiredSpecificationsControl Circuit Connection:Tinned WireNominal Voltage:24V DCManual Control: YesCoil Function: Auto releasing Mounting:t#10Amperage Operating Current:8mA when OFF/13mA when ONAmperage Operating Current when changing state:t<4A (40 ms)Control Circuit Voltage:t20.2 to 32.9V DCContinuous Rating: 500AIntermittent Rating: t700A (5 min)Cranking Rating: 10 sec 2500ACranking Rating: 1 min 1100AMinimum Operating Temperature:t-10° CMaximum Operating Temperature:t50° CCable Size to Meet Ratings:t2x (4/0)Live Current Switching:t300A @ 12V DC 10,000 CyclesMaster Control Switch Capability:tYesMechanical Endurance:t100,000 CyclesSwitching Cycles:t100000Terminal Ring Diameter Clearance:t1.18" (29.97mm)Terminal Stud Length:t0.875" (22.23mm)Terminal Stud Size:t3/8-16 (M10)Terminal Stud Torque:t140 in-lb (15.82 Nm)Weight:t1.75lb (0.79 kg)WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Lockable: Yes Continuous Amperage: 500a Box Dimensions: 3"H x 7"W x 12"L WT: 2.2 lbs UPC: 632085077143 Owner's Manual (pdf)Brochure (pdf)

Read more less

T-H FLEX™ 1-1/4" Expandable Braided Sleeving - 50' RollT-H FLEX™ is a lightweight, braided jacketing for bundling and protecting wires, cables and hoses. Braided from high temperature yarns, T-H FLEX™ offers total protection for wire and cable assemblies. The unique expansion characteristics makes T-H FLEX™ easy to slip on. Only a few sizes are needed to cover a large diameter range, since each size of T-H FLEX™ expands up to four times its normal diameter.  The sleeving cuts easily and cleanly with a hot knife and once installed, will beautify and protect any wire, hose or cable application.Features: Lightweight Protective Sleeving Protects Wire, Cables and Hoses Braided from High Temperature Yarns Chemical Resistant Simplifies and beautifies any rigging application Specifications: Type: Misc Box Dimensions: 6"H x 9"W x 10"L WT: 1.45 lbs UPC: 733572036756

Read more less

29/31 Battery Tray with StrapsA simple-to-install battery holder that fits into limited spaces. This tray is for batteries up to 10-1/2 inches in height. Provide a simple installation for changing or replacing batteries.Features: The polypropylene hold-down strap has a positive-locking, quick-disconnect buckle Molded base mounts with four #10 Panhead fasteners Specifications:Inside Dimensions: 12-7/8" L x 7" W Quick Guide (pdf)

Read more less

36" SAE Power Cable Polarized Electrical ConnectorThis SAE-type polarized electrical connector is a two-prong plug and socket connector set. Features:14-gauge duplex wireSpecifications: Length: 36 in. Volts: 12-24 Max Amps: 20A @ 12V Wire Gauge: 14 AWM Weight: 0.17 lb. Specifications: Type: Cables Box Dimensions: 1"H x 5"W x 9"L WT: 0.15 lbs UPC: 035514432757 Brochure (pdf)

Read more less

12-12-3i Power StabilizerFeed sensitive electronics with proper voltage, regardless of the battery condition. This stabilizing converter provides continuous, precisely regulated output over the entire range of a battery’s usable voltage. This prevents subjecting loads to fluctuating input voltage, which can cause shutdown, diminish performance, and possibly damage sensitive circuitry.This converter provides total input/output isolation, virtually eliminating conducted line noise and permitting the connection of negative ground gear to positive or floating ground systems, or vice versa. It can be modified for use as a battery charger, allowing them to maintain a battery at a great distance from the primary voltage source, providing reserve power if the main source fails. The rugged anodized aluminum case is ideal for marine applications.Application Benefits Include: Operate electronics at optimal input voltage, even from nearly drained batteries Boost voltage to compensate for voltage drops in long wire runs from batteries Eliminate voltage drops during momentary high current drain from batteries, as during engine start Eliminate voltage fluctuation from charge sources Eliminate voltage overshoot due to sudden removal of high current load Specifications: Input Voltage: 10-16 Input Amps: 4 Output Voltage: 13.6 Output Amps (Intermittent): 3 Output Amps (Continuous): 3 Case Size (H x W x D): 3.5 x 3.5 x 1.75 inches (8.9 x 8.9 x 4.5 centimeters) Weight: 1 lb. (.45 kg) Output: 12 or 24V, nominal, see matrix Ripple: 150 mV P-P maximum Regulation: 1% Line/Load Duty Cycle Ratings: Intermittent: 20 minutes max on time, 20% duty. Current limit is set at approx. 105% of intermittent rating. Continuous: 24 hours, 100% duty Idle Current: Less than 100 mA (including power “ON” light ) Operating Temp: 0-50 degrees C, Derate Linearly From 100% @ 40 degrees C To 50% @ 50 degrees C. Thermal shutdown @ 70 degrees C Case Temperature. Switching Frequency: 40 kHz. Efficiency: 85% – Typical. Isolation – Output/Chassis; Input/chassis: 250 VDC Mechanical Specifications: Anodized aluminum heat sink case Front panel terminal block Heavy-duty mounting flange Conformal-coated PC board Options/Factory Modifications: Operation as a battery charger (contact factory) Parallel/redundant operation (contact factory) High-vibration mounting kit Non-standard output voltage (contact factory) Option: Extreme Vibration Mounting KitThe Extreme Vibration Mounting Kit is available to protect NEWMAR power converters from the extreme stresses of shock and vibration when mounted on high-vibration vehicles.The kit (pictured here) replaces the standard vibration kit provided with the unit and fits into the unit’s mounting flange to act as a “super shock absorber” for electronics in high-vibration applications. It is available to fit all NEWMAR units from 2 to 70 lbs. Specify KIT–L for units that weigh 2–15 lbs. and Kit–H for units that weigh 16-70 lbs.This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Read more less

Locking Connector - 15A, 125V - YellowThe 4731CR 15A 125V straight blade female shore power connector features corrosion-resistant contacts and terminals. The body is made of yellow nylon with a ribbed design for a secure grip.

Read more less

Splash Guard Bilge Pump Panel with CircuitThe Splash Guard Bilge Pump Panel features a splash guard switch cover making this panel ideal for applications where the front might be subjected to light spray or water (NOT designed for total water immersion). This deluxe version features a three-way switch allowing both automatic and manual switching of the bilge pump. When operated in Manual mode, a red LED light is activated. When in Automatic mode, a green LED light is activated. The panel is designed so the words “Bilge Pump" will illuminate when back lit, allowing for easy location and operation at night. UL listed 20A circuit breaker included. Additional breaker sizes available (420805-420830). Constructed of injection molded ABS for maximum durability and corrosion resistance. Installs with four #6 RH fasteners (not included). WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Water Resistant Toggle Switch Panel Water Resistant Toggle Switch Panel is constructed of injection molded ABS and polycarbonate. Features six 15A 12VDC toggle switches with blue LED indicator lights, ATC fuse holders, and decal sheet. Rated IP66. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Waterproof: Resistant Box Dimensions: 4"H x 6"W x 9"L WT: 0.8 lbs UPC: 035514428903

Read more less

10 Key Kill Switch Universal Lanyard This marine emergency cut-off 10 Key Universal Kill Switch with Lanyard attaches to your life vest while operating a boat or personal watercraft. Designed to instantly cut battery power when detached. Constructed of injection molded nylon and Delrin. The 10 key 50” lanyard fits Johnson, Evinrude, Mercury, Yamaha, Honda, Tohatsu, Suzuki, Kawasaki, OMC, and Nissan kill switches. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Plastic Motion Sensor Switch with Delay for LED LightsMotion Sensor Switch can be used to activate LED and incandescent lights. The motion detection range is up to 15 feet, with an activation angle of 120°. Activation time is adjustable (10/20/50/70 seconds); factory preset 70 seconds. 2A max. 12-30VDC. IP67 waterproof rating. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Battery Tray with Straps for 24 Series Batteries Heavy duty Battery Tray with Strap for size #24 batteries. Includes hold down strap with a quick release buckle and four 1/4"x1" PH screws with washers. Injection molded polypropylene construction.WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less