Electrical

SS Switch - 7.5 AC Selector SwitchThis AC source selector switch is an essential item for any vessel with an onboard AC generator and/or inverter. By isolating power source inputs, the switch eliminates the safety hazard and/or damage that can occur if two AC sources are applied to the same circuit simultaneously.The switch is fitted with a compact escutcheon plate with engraved switch position nomenclature.The switches carry cUL approval, are CE-marked, and feature heavy-duty contacts and a positive step cam mechanism for low-resistance contact closure. Features:Maybe rear-mounted in a panel with a thickness of up to 1/4”Specifications: Amperage @ 115/230V: 63 Number of Poles: 2 Switch Positions: 2 + “OFF” Standard Plate Markings: SHIP-OFF-SHORE     Depth Dimensions: 2-3/8 in.

Read more less

Current Model Mercruiser Solenoid with Raised Isolated BaseMercruiser solenoid that will fit Mercruiser and Mercury, Isolated base, 12 Volt.Replaces:MERCURY 8M0123161MERCURY 89-846070MERCURY 89-94318MERCURY 89-96158MERCURY 89-96158T*ARCO Assurance 12-month part and labor warranty protectionThis product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Specifications: Type: Parts Box Dimensions: 3"H x 4"W x 4"L WT: 0.38 lbs UPC: 693006001623

Read more less

15A 125V On-Board Charger Inlet - Front Mount - WhiteMarinco on-board charger inlets make battery charging through an on-board battery charger safer and more convenient. Inlets mount on the boat exterior and are hard-wired directly to the charger. To use, just open the flip lid cover and plug an extension cord into the inlet. All hatches remain closed and locked throughout the charging cycle for added security.WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Amperage: 15a Type: Inlets Voltage: 125v Box Dimensions: 3"H x 5"W x 9"L WT: 0.35 lbs UPC: 093344304873

Read more less

Front Mount Power SocketThis SAE-type polarized electrical connector is a two-prong power socket connector set. Great for solar panel connections and maintaining battery charge. Drill a 3/4” hole and install with two #10 RH screws (not included).Features:14-gauge duplex wireSpecifications: Length: 5 in. Volts: 12-24 Maximum Amps: 20A @ 12VDC Wire Guage: 14 AWM Weight: 0.12 lb. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Quick Guide (pdf)

Read more less

Mini Battery Switch Key with Removable Knob - 32V & 300AThese Mini Battery Switches feature a removable knob for extra security. To remove, simply twist the cap to the OUT position and pull. Mini footprint makes it ideal for close quarters. The 422730-1 is rated at 300A continuous and 1000A cranking amps. Installation is as easy as drilling a 2-1/16" hole for the 422730-1, inserting the socket body, tightening the locking nut, and connecting the wires. Features:  3 Switch positions: On, off, and out Constructed of machined brass and injection molded nylon Specifications: Switch Face Width: (inch) 2-1/16" Volts: 32 Amps: 300 Stud Diameter: (inch) 5/16" WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Continuous Amperage: 300 Positions: 3 Box Dimensions: 3"H x 4"W x 7"L WT: 0.4 lbs UPC: 035514432887

Read more less

Battery Box Strap & Brackets - 38" Battery Box Strap & Brackets includes a woven polypropylene strap, injection molded nylon buckle, two brackets, and four #8 FH fasteners. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

DS6-P Vertical Cable SealScanstrut premium IP68 waterproof cable seal provides easy-fit cable routing that cuts down your installation time and is the only guaranteed and proven watertight installation for your antenna and navlight cables. Features: Watertight installation - 100% waterproof with an IP68 rating Easy and reliable installation - each unit is supplied with both pre-drilled and blank inner seals to make your installation as easy as possible.  No Need to Remove Cable Connectors - split-seal option does not require connector removal during installation.  Multi-Functional Dome Shape - the aesthetic dome-shaped profile provides a stronger, impact-resistant design and the outer dome provides an additional water shield. Technical Specifications: Fits cable size (diameter) - .08" to .24" (2 - 6 mm)   Fits connector size up to .24" (6 mm) in diameter  Height - .67" (17 mm) Color - Grey Orientation - Vertical Material - ASA Plastic In the Box: Cable seal Mounting hardware Installation manual  *Sold as an Individual Specifications: Type: Deck Seal Box Dimensions: 1"H x 4"W x 9"L WT: 0.14 lbs UPC: 5060114794924 Quick Guide (pdf)Brochure (pdf)

Read more less

MultiPlus-II 12/3000 - 120-50 - 2x 120V (UL 458)The MultiPlus-II combines the functions of the MultiPlus and the MultiGrid. It has all the features of the MultiPlus, plus an external current transformer option to implement PowerControl and PowerAssist and to optimize self-consumption with external current sensing (max. 32A).It also has all the features of the MultiGrid with built-in anti-islanding and an increasingly long list of country approvals.PowerAssistThe MultiPlus-II will prevent the overload of a limited AC source, such as a generator or shore power connection. First, battery charging will automatically be reduced when otherwise an overload occurs. The second level will boost the output of a generator or shoreside supply with power taken from the battery.ESS: Energy Storage SystemsThe MultiPlus-II is the critical component in a Victron ESS system, providing the flexibility to combine with MPPT Solar Chargers or Grid-tie PV Inverters. For examples and more detailed information see the ESS (Energy Storage System) manual.Uninterrupted AC Power (UPS function)In the event of a grid failure, or when shore or generator power is disconnected, the inverter within the Multi is automatically activated and takes over the supply to the connected loads. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption.Remote Monitoring & ControlWhen coupled with a GX device (e.g. Cerbo GX) you can monitor and control your Multi and system or systems' locally (LAN) or remotely via the internet from anywhere in the world, using the free VRM app and free VRM portal website. Access can be from a phone, tablet, laptop, or PC for multiple operating systems. There is no end to the level of control, from adjusting your Multi to auto-starting a backup generator and more.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)Owner's Manual (pdf)Brochure (pdf)

Read more less

BI-100 Battery IntegratorCharging multiple battery banks without the use of diode isolators dictates that the batteries be connected or “integrated” only whenever a charge voltage is present so that they may be charged simultaneously, then disconnected or “isolated” when the charge voltage is no longer present to allow for selective discharge and avoid having the secondary or standby battery drain into the primary battery.Battery integrators perform this function automatically, acting as a “smart” switch to connect independent battery banks only when a charging voltage is present. Otherwise, they are isolated, and discharge between banks is prevented.The Battery Integrator causes no voltage drop in the charging system, while the multiple batteries are charged as a single bank whenever a charging source of approximately 13.2 VDC or 26.4 VDC or greater is present (depending on the model).When the alternator or charger is off or a large load causes the voltage to drop below the disconnect point, the unit breaks the common tie between the banks. This allows selective battery discharge and prevents the “dumping” of a higher-charged bank into a lower-charged bank. The unit may also be remotely activated to connect other batteries through the key starter or a manual switch to provide an added “boost” from the secondary battery whenever the starter is engaged and the unit senses there is sufficient voltage in that battery to provide an assist.Features: Enables charging of two separate banks without voltage drop yet maintains 100% isolation at all other times. For systems of three banks or more, an additional unit must be installed for each additional bank Heavy-duty silver-plated contactor, continuous duty rated to 100 Amps or 200 Amps depending on model Voltage sense circuits, epoxy-encapsulated, and heavy-duty continuous-rated solenoids are all designed for use in marine environments 12 volt, 100 amp model has an ignition protection rating Has ignition protection rating Easy three-wire hookup for two bank systems (BATT +, BATT +, GROUND) Terminal for optional wiring of a remote light indicating when battery banks are integrated Optional internal connections can be wired through the key starter or manual override switch, tying battery banks together for an extra boost during engine start Specifications: Terminals: Battery Connections: 5/16 in. copper alloy stud Approvals: CE Marked Dimensions (H x W x D): 100 Amp Models: 3 x 3.25 x 2.5 inches Weight: 1 lb. Operating Temperature: Control: -40 to +85 degrees C and Solenoid: -28 to +48 degrees C Voltage: 12 VDC Battery Integration Point: 13.2 VDC     Battery Disconnect Point: 12.8 VDC Max. Continuous Current: 100 Amps     Peak Maximum Current: 400 Amps

Read more less

Lead Battery Terminal - 5/16" & 3/8" Stud - Positive & Negative Combo PackStud Size:5/16 " & 3/8"Product Features: Seamless barrel design allows for maximum strength when crimped Closed end design seals out moisture so cables stay dry and corrosion free WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Type: Battery Terminals Post Size: 5/16" & 3/8" Package Qty: 2 Heat Shrink: No Box Dimensions: 1"H x 1"W x 1"L WT: 1.5 lbs UPC: 091887263251 Quick Guide (pdf)

Read more less

Medium Cable Gland - #14-#10 CableSMS Enclosure Gland PG16Accepts Cable #14-10 (3 Conductor)WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Type: Deck Seal Box Dimensions: 1"H x 2"W x 4"L WT: 0.05 lbs UPC: 632085031251

Read more less

MultiPlus-II 24/3000 - 70-50 - 120V - UL 458The MultiPlus-II, an inverter/charger, combines the functions of the MultiPlus and the MultiGrid. It has all the features of the MultiPlus, plus an external current transformer option to implement PowerControl and PowerAssist and to optimize self-consumption with external current sensing (max. 32A). It also has all the features of the MultiGrid with built-in anti-islanding and increasingly long list of country approvals.PowerAssistThe MultiPlus-II will prevent the overload of a limited AC source, such as a generator or shore power connection. First, battery charging will automatically be reduced when otherwise an overload would occur. The second level will boost the output of a generator or shoreside supply with power taken from the battery.ESS: Energy Storage SystemsThe MultiPlus-II is the key component in a Victron ESS system, providing the flexibility to combine with MPPT Solar Chargers or Grid-tie PV Inverters.Uninterrupted AC power (UPS function)In the event of a grid failure, or when shore or generator power is disconnected, the inverter within the Multi is automatically activated and takes over the supply to the connected loads. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will operate without disruption.Remote Monitoring and ControlWhen coupled with a GX device (e.g. Cerbo GX) you can monitor and control your Multi and system or systems' locally (LAN) or remotely via the internet from anywhere in the world, using the free VRM app and free VRM portal website. Access can be from a phone, tablet, laptop or PC for multiple operating systems. There is no end to the level of control, from adjusting your Multi to auto starting a backup generator and more.Specifications:  PowerControl & PowerAssist: Yes Transfer Switch: 50A Maximum AC Input Current: 50A Inverter Specifications: DC Input Voltage Range: 19–33 V Output: Output Voltage 120 VAC ± 2% / Frequency 60 Hz ± 0,1% (1) Continuous Output Power at 25°C (3): 3000 VA Continuous Output Power at 25°C: 2400 W Continuous Output Power at 40°C: 2200 W Continuous Output Power at 65°C: 1700 W Maximum Apparent Feed-In Power: 2500 VA Peak Power: 5500 W Maximum Efficiency: 94% Zero Load Power: 13 W Zero Load Power in AES Mode: 9 W Zero Load Power in Search Mode: 3 W Charger Specifications: AC Input: Input Voltage Range 90-140 VAC / Input Frequency: 45 – 65 Hz Charge Voltage 'Absorption': 28,8 V Charge Voltage 'Float': 27,6 V Storage Mode: 26,4 V Maximum Battery Charge Current (4): 70 A Battery Temperature Sensor: Yes General Specifications: Auxiliary Output: Yes (32 A) External AC Current Sensor (optional): 100 A Programmable Relay (5): Yes Protection (2): a – g VE.Bus Communication Port: For parallel, split phase and three phase operation, remote monitoring and system integration General Purpose Com. Port: Yes, 2x Remote On-Off: Yes Operating Temperature Range: -40 to +65°C (-40 – 150 °F) (fan assisted cooling) Humidity (Non-Condensing): Max 95% Enclosure Specifications: Material & Color: Steel, blue RAL 5012 Protection Category: IP22 Battery-Connection: M8 bolts 120 V AC-Connection: Screw terminals 13 mm² (6 AWG) Weight: 9 kg Dimensions (hxwxd) (mm): 536 x 277 x 147 Standards: Safety: EN-IEC 60335-1, EN-IEC 60335-2-29, UL458 Emission, Immunity: EN 55014-1, EN 55014-2, EN-IEC 61000-3-2, EN-IEC 61000-3-3, IEC 61000-6-1, IEC 61000-6-2, IEC 61000-6-3 *Note: For a short period of time this product was called MultiGrid-II.Please contact your dealer for any returns, repairs or support issues related to this product. Specifications: Charger Input - Voltage: 120VAC Charger Output - Amps: 70A Charger Output Voltage: 24VDC Charging Banks: 2 Inverter Cont. Output Wattage: 3000VA / 2400W Inverter Input Voltage: 24VDC Inverter Output Voltage: 120VAC Outlet Qty: None Box Dimensions: 10"H x 14"W x 23"L WT: 48.25 lbs UPC: 8719076059202 Quick Guide (pdf)Owner's Manual (pdf)Brochure (pdf)

Read more less