Marine Hardware

Screw-Out Deck PlateThe Beckson Screw-Out Plate was designed to provide access without the use of tools, with a single start non-jamming (no cross-thread), extra strong, self-cleaning buttress thread. They incorporate a self-aligning center and an innovative gasket to assure a watertight seal. A back-up sealing wall leaves the plate watertight, even if the gasket is removed. Our clear center plates permit observation of controls or gauges and visual inspection without the necessity of removing the center. Deck plates are used for access to shut-off valves or back-fastenings, inspection, and clean out for tanks and compartments. A screw-out plate should be used in compartments where a change in air pressure due to temperature or oil canning can occur. Center: Clear Color: Black

Read more less

3-Step Telescoping Swim LadderFeatures: 304 Stainless Steel with plastic treads Includes mounting hardware 1" diameter tubing 3 Steps Telescopes for compact storage on top of platform Velcro hold down strap No Platform Included Extended: 35-1/2"L x 11"W Collapsed: 14-3/4"L x 11"W

Read more less

7-1/2" Gas Spring - 20lb - Black NitrateFeatures: Black Nitrate Gas Spring Ext. Length - 7-1/2" Comp. Length - 5-1/2" Rod Dia. - 6mm Tube Dia. - 15mm P1 Force - 20 Specifications: Lift Capacity: 20 lbs Length: 7-1/2" Box Dimensions: 1"H x 1"W x 10"L WT: 0.25 lbs UPC: 725060312015

Read more less

Four Insulated Drink/Binocular Rack 16-1/2"L x 4"W x 3-1/2"H Larger holes hold 4 glasses or cans in insulated drinkholders or 2 glasses or cans in insulated drinkholders and one pair of binoculars

Read more less

Flush Pull Ring Size:1-1/2" x 1-3/4" Fastener:#6(4) Material:Chrome Plated Brass WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Outboard Motor Bracket - Stainless Steel - Max 10HPStainless Steel Outboard Motor Bracket Up to 10 horse power. The Adjustable outboard motor bracket is stainless steel construction and non-corrosive for saltwater use. Designed for use with power or sail boats. Manual operation means no power required to raise and lower your auxiliary outboard motor. Features Stainless Steel Construction Fits Motors up to 10 horse power at 110 pounds.14" travel.

Read more less

Open Base CleatChrome Plated Zinc AlloyLength Overall: 4"Dimensions Base: 2-1/8" x 1-1/2"Max Rope Size: 5/16" Specifications: Finish: Chrome Construction: Zinc Size: 4" Box Dimensions: 2"H x 4"W x 8"L WT: 0.6 lbs UPC: 085226369391

Read more less

Chrome Plated Zinc Cabin Door Hook - 1-3/4"Features:Chrome Plated Zinc Alloy

Read more less

Grabber Catch Latch - Side Mount - Black - Pull-Up Force 22N (5lbf)Features: Spring-loaded over-center latching One assembly includes catch and keeper Material and Finish: PC/ABS, black Performance Details: Operating temperature range: -30ºC (-20ºF) to 60ºC (140ºF) Flammability rating: UL94-HB Installation Notes: Orient keeper to latch. The arrow on the keeper should point towards the cam. Mount to door and adjust for smooth latching. Minimum distance from frame (or surface on which catch subassembly is mounted) to centerline of door hinge is 150 (5.9)

Read more less

Round Flush Ring Pull - 2" - Chrome Plated ZincSpecs: Chrome plated zinc alloy Face Plate O.D.: 2" Screw Size: 6

Read more less

PSS Shaft Seal 1-1/2" Shaft 2-1/2" TubeShaft Diameter: 1-1/2"Stern Tube Diameter (D): 2-1/2" to 2-5/8"Total Length (A): 9.175"Total Length (compressed) (Compressed A): 8.175"Rotor Diameter (B): 3.75"Carbon Cuff Diameter (C): 3.25"Stern Cuff Length (E): 2"The PSS Shaft Seal is the number one selling marine mechanical seal worldwide and is installed as standard equipment by many of the worlds most reputable boat builders / yards. The PSS Shaft Seal is also recognized as the premiere retrofit (aftermarket) seal on the world market. Certified by Bureau Veritas, ABS & Rina: Boat builders / yards recognize the advantages and value of installing the PSS as it eliminates the maintenance, constant adjustment & cost associated with traditional packing type glands. Aside from these benefits, the PSS Shaft Seal helps to eliminate water in the bilge (100% water tight) & wear to the propeller shaft. The PSS Shaft Seal can be easily retrofitted and is available for shafts ranging from 3/4" (20mm) to 6" (150mm).The PSS Shaft Seal is a mechanical face seal that is created between the flat surfaces of the rotating stainless steel rotor and the stationary carbon flange. The stationary carbon flange is attached to the vessels stern tube with hose clamps and the carbon flange is attached to the front side of the bellows with hose clamps. The stainless steel rotor is fit on the shaft in front of the carbon flange. The stainless steel rotor is used to compress the bellows before the collar is secured to the shaft with set-screws. This compression (pre-load) maintains contact between the faces and allows the PSS to compensate for the thrust from the propeller. The carbon flange is bored larger than the shaft diameter allowing it to "float" around the shaft and thus compensate for most misalignment and vibration problems. The stainless steel collar is sealed to the shaft by two o-rings that are recessed into the bore of the collar. These o-rings rotate with the shaft and stainless steel rotor and do not experience wear during operation.**As with any rubber hose below waterline, the PSS bellows must be inspected on a regular basis for any sign of wear, aging or chemical deterioration. PYI suggests as preventative maintenance that the PSS bellow be replaced in six year intervals. During bellows replacement it is recommended the o-rings & set screws in the stainless steel rotor also be replaced."Bellows may need to be more frequently inspected in an environment where non-sealed batteries emit sulfuric acid. Sulfuric acid vapor will accelerate rubber deterioration, as will an ozonater.The Maintenance Kit includes the items you need to properly maintain your PSS Shaft Seal. Included in the kit is one (1) PSS bellow, two (2) O-rings, five (5) set screws, four (4) new hose clamps and an allen key. Brochure (pdf)

Read more less

Screw-Out Deck PlateThe Beckson Screw-Out Plate was designed to provide access without the use of tools, with a single start non-jamming (no cross-thread), extra strong, self-cleaning buttress thread. They incorporate a self-aligning center and an innovative gasket to assure a watertight seal. A back-up sealing wall leaves the plate watertight, even if the gasket is removed. Deck plates are used for access to shut-off valves or back-fastenings, inspection, and clean out for tanks and compartments. A screw-out plate should be used in compartments where a change in air pressure due to temperature or oil canning can occur. Center: Smooth Color: White

Read more less