Marine Hardware

V46 - 13.5" Stainless Steel Steering Wheel with Speed KnobFeatures: Polished stainless steel Speed knob included Steering wheels are CE marked in conformity with the EN 28848 – EN 29775 and ABYC P22 safety standards Specifications: Diameter: (inch) 13.5" 3 spokes *Note: Wheel nut is not included and is needed for installation

Read more less

PSS Shaft Seal 1-1/2" Shaft 2-1/2" TubeShaft Diameter: 1-1/2"Stern Tube Diameter (D): 2-1/2" to 2-5/8"Total Length (A): 9.175"Total Length (compressed) (Compressed A): 8.175"Rotor Diameter (B): 3.75"Carbon Cuff Diameter (C): 3.25"Stern Cuff Length (E): 2"The PSS Shaft Seal is the number one selling marine mechanical seal worldwide and is installed as standard equipment by many of the worlds most reputable boat builders / yards. The PSS Shaft Seal is also recognized as the premiere retrofit (aftermarket) seal on the world market. Certified by Bureau Veritas, ABS & Rina: Boat builders / yards recognize the advantages and value of installing the PSS as it eliminates the maintenance, constant adjustment & cost associated with traditional packing type glands. Aside from these benefits, the PSS Shaft Seal helps to eliminate water in the bilge (100% water tight) & wear to the propeller shaft. The PSS Shaft Seal can be easily retrofitted and is available for shafts ranging from 3/4" (20mm) to 6" (150mm).The PSS Shaft Seal is a mechanical face seal that is created between the flat surfaces of the rotating stainless steel rotor and the stationary carbon flange. The stationary carbon flange is attached to the vessels stern tube with hose clamps and the carbon flange is attached to the front side of the bellows with hose clamps. The stainless steel rotor is fit on the shaft in front of the carbon flange. The stainless steel rotor is used to compress the bellows before the collar is secured to the shaft with set-screws. This compression (pre-load) maintains contact between the faces and allows the PSS to compensate for the thrust from the propeller. The carbon flange is bored larger than the shaft diameter allowing it to "float" around the shaft and thus compensate for most misalignment and vibration problems. The stainless steel collar is sealed to the shaft by two o-rings that are recessed into the bore of the collar. These o-rings rotate with the shaft and stainless steel rotor and do not experience wear during operation.**As with any rubber hose below waterline, the PSS bellows must be inspected on a regular basis for any sign of wear, aging or chemical deterioration. PYI suggests as preventative maintenance that the PSS bellow be replaced in six year intervals. During bellows replacement it is recommended the o-rings & set screws in the stainless steel rotor also be replaced."Bellows may need to be more frequently inspected in an environment where non-sealed batteries emit sulfuric acid. Sulfuric acid vapor will accelerate rubber deterioration, as will an ozonater.The Maintenance Kit includes the items you need to properly maintain your PSS Shaft Seal. Included in the kit is one (1) PSS bellow, two (2) O-rings, five (5) set screws, four (4) new hose clamps and an allen key. Brochure (pdf)

Read more less

Marine Outboard Motor Bracket - Stainless Steel - Fixed 15HPFeatures: For engines up to 12hp and 85 lbs max weight (39kg). Heavy-duty Stainless Steel. Rugged Polypropylene mounting board (2" [5cm] thick). Includes mounting hardware. recommend using safety cable— not included Owner's Manual (pdf)

Read more less

Screw-Out Deck PlateThe Beckson Screw-Out Plate was designed to provide access without the use of tools, with a single start non-jamming (no cross-thread), extra strong, self-cleaning buttress thread. They incorporate a self-aligning center and an innovative gasket to assure a watertight seal. A back-up sealing wall leaves the plate watertight, even if the gasket is removed. Our clear center plates permit observation of controls or gauges and visual inspection without the necessity of removing the center. Deck plates are used for access to shut-off valves or back-fastenings, inspection, and clean out for tanks and compartments. A screw-out plate should be used in compartments where a change in air pressure due to temperature or oil canning can occur. Center: Clear Color: White

Read more less

6" Folding Cleat - Stainless SteelFeatures: Folding Cleat Made with 316 Stainless Steel Length - 6" For top mount applications where depth under the deck is a concern Specifications: Size: 6" Finish: Polished Construction: Stainless Steel Box Dimensions: 1"H x 3"W x 7"L WT: 0.8 lbs UPC: 725060674632

Read more less

17" Gas Spring - 40lb - Black NitrateFeatures: Black Nitrate Gas Spring Ext. Length - 17" Comp. Length - 10-1/4" Rod Diameter - 6mm Tube Diameter - 15mm P1 Force - 40 Specifications: Length: 17" Lift Capacity: 40 lbs Box Dimensions: 1"H x 1"W x 18"L WT: 0.4 lbs UPC: 725060364014

Read more less

T-Handle Latch - Nylon Black/Black - LockingFeatures: Threaded offset cam bar with set screw included Neoprene O-Ring Shaft is 1-3/8" long unless otherwise noted Specifications: Outer Diameter: 3" Cut-Out: 2-1/2" Surface Depth: 1/8" - 3/4" Fastener: Included

Read more less

90 degree Gas Vent. Picture of product is the center image. Round Head. Hose is 3/4", Hole size is 9/16"

Read more less

PU50 14" Wheel - Chrome Cap & Spoke Inserts - Black Spokes - 3/4" Tapered ShaftThis particular model of the PU50 Wheel is a black polyurethane steering wheel with black spokes. Best suited for ski boats, wakeboard boats, runabouts, or pontoons that run in freshwater applications.Features: Chrome cap & spoke inserts  The wheel is made of polyurethane Black anodized aluminum spokes Specifications: Rim diameter: (inch) 14" Hole diameter: (inch) 3/4" tapered hub 3 spokes

Read more less

TR3 Spring Loaded Safety Pin - 1/4" ShackleFeatures: Hitch pin lock for device locking safety Computer generated parts precision-cut from aerospace grade stainless steel plate Low friction, low effort lanyard-style release for maximum user safety All parts 100% stainless steel WARNING: This product can expose you to chemicals including Titanium dioxide which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

Read more less

SuproFlex Rub Rail Kit - White with Flex Chrome Insert - 2"H x 1.2"W x 60'LThe SuproFlex Rub Rail Kit is lightweight and ultra-flexible to save you time and money while providing a seamless precision fit. The innovative SuproFlex series is co-extruded vinyl that provides two levels of hardness – ensuring enhanced protection from impact. SuproFlex Rub Rail requires minimal heating – reducing installation time and manpower. Additionally, SuproFlex Rub Rail requires no pre-forming and easily molds to most hull shapes. Features: Ideal for boats up to 65' Co-extruded to provide two levels of hardness Rigid backing and soft durometer front Shock-absorbing channels for higher impact resistance Lighter weight than traditional vinyl rub rail Requires no pre-forming and minimal heating Pairs with V12-0307CP (included in kit) Made in the USA 5-year limited warranty This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Read more less

Offset Short Cam BarFeatures: Zinc Replacement Cam Bar - Offset (Short) Size - 2-1/4" Shaft - 3/8" (metric threads)

Read more less