Marine Navigation & Instruments - Accessories

Protective Cover for ECHOMAP Plus/UHD 9" UnitsUse our cover to protect your compatible ECHOMAP Plus from the harsh marine environment when not in use. Specifications: Type: Covers Box Dimensions: 1"H x 7"W x 13"L WT: 0.55 lbs UPC: 753759275570

Read more less

Replacement KnobThis Garmin replacement bail mount knob is compatible with Garmin's bail mounts.Features: It helps secure a compatible VHF radio 20mm knob size

Read more less

12" Protective Cover - PlasticKeep your compatible GPSMAP device safe from the harsh marine environment, when not in use, with this plastic protective cover.Compatible Units: 8412/8412xsv 8612/8612xsv WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Type: Covers Box Dimensions: 1"H x 9"W x 12"L WT: 0.53 lbs UPC: 753759219123

Read more less

Protective Cover for STRIKER™/Vivid 9" UnitsUse our cover to protect your compatible STRIKER™ from the harsh marine environment when not in use. Specifications: Type: Covers Box Dimensions: 2"H x 7"W x 14"L WT: 0.55 lbs UPC: 753759275624

Read more less

HDMI to IP Encoder - Converts HDMI to IP - Compatible with Raymarine, Simrad & FurunoConvert your HDMI video source to a high-definition IP stream compatible with Raymarine, Simrad, B & G, and Furuno Chart-Plotters using the HDMI2IP-01 Single Channel Encoder from Iris Innovations.This small and compact little box takes your HDMI video and uses H.265 / H.264 compression algorithms to encode the video into a high-definition IP stream which leading a chartplotters process as if it were an IP camera device. Simply configure the device to sit on your MFD network, hook up your HDMI camera, and then configure your MFD in the same way you would configure an IP camera. If your MFD works as an RTSP server (such as Raymarine Axiom and Furuno TZT devices) simply set the HDMI2IP unit to accept its IP address via RTSP and you are good to go.Your MFD will treat the stream as if it were an IP camera, which means once configured, the video will display on all compatible devices connected to your MFD network, greatly simplifying installation.The device is powered from your vessel (or vehicle’s) +12VDC supply and draws less than 200mA.Features: Converts High Definition HDMI video into IP video streams using H.265 / H264 Compression Compatible with Raymarine, Navico (Simrad / B & G), and Furuno Chart-Plotters HDMI Devices Handled as IP Cameras by Compatible MFD’s Perfect for Displaying HD Video Ouput from CMAC on your Chartplotter Connect to the MFD Network to View Video on all Connected, Compatible Devices Low Power, +12VDC Operation. Small, Compact, and Easy to Install Supports Audio Can be Used to Encode any HDMI Video Source This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Read more less

veKonvert NMEA 2000 GatewayveKonvert brings NMEA 2000 connectivity to Victron’s popular SmartShunt battery monitoring system. Now a navigation multi-function display becomes a sophisticated battery and energy management system.FeaturesveKonvert is a stand-alone NMEA 2000 interface designed in conjunction with Victron Energy to integrate VE.Direct compatible devices such as their SmartShunt, BMV Battery Monitors, and MPPT Solar Charge Controller range into NMEA 2000 systems.This functionality already existed but required the use of a sophisticated Cerbo module. veKonvert is a lower-cost, simpler solution for smaller installations that just need the electrical data displayed on a multi-function display.Boaters and boat builders like a clear and uncluttered dash or nav area, so integrating electrical data into the main navigation display is a popular and cost-saving option.The product is a collaboration between Victron Energy and Digital Yacht. The system utilizes Victron’s proprietary VE.Direct data connectivity as a source for the NMEA 2000 data.Victron solar charge controllers (MPPTs) and battery monitors can now also interconnect to your NMEA 2000 MFD via the veKonvert interface.InstallationInstallation is simple – just "T" into the NMEA 2000 backbone and plug into the VE.Direct custom connector on the SmartShunt, and you've got battery and electrical data on your NMEA 2000 network!  Note that one veKonvert is required for each battery bank.Specifications: Universal NMEA 2000 gateway for Victron products with a VE.Direct interface Enables battery management or solar charge monitoring on compatible multi-function displays (Raymarine, Garmin, Navico, Furuno, etc) Provides battery voltage, charge/discharge current, state of charge, and time to depletion based on a sophisticated algorithm Easy installation, plug ‘n’ play connectivity, and self-powering from the NMEA 2000 bus Generates NMEA 2000 alerts from any BMV or SmartShunt Alarms Supports multiple SmartShunts for a larger multi-battery system VeKonvert Is Compatible with the Following Victron Products:BMV-700, BMV-702, BMV-700H, BMV-712 Smart, BMV-710H Smart, BMV-712 Smart, SmartShunt 500A/50mV, SmartShunt 1000A/50mV, SmartShunt 2000A/50mV, and All MPPT Charge ControllersThe veKonvert will automatically detect what Victron device it is connected to and adjust the NMEA 2000 data that it outputs accordingly. Below is a list of the PGNs that the veKonvert outputs for the different Victron Devices and different modes that they can operate in:  All MPPTs PGN 127506 DC Detailed Status (DC Type set to MPPT) PGN 127508 Battery Status (MPPT Output Voltage and Current) PGN 130900 Proprietary Solar Controller (All solar panel data) All SmartShunts and BMVs PGN 127506 DC Detailed Status (DC Type set to Battery, SOC and A/h consumed) PGN 127508 Battery Status (Output Voltage and Current) NOTE: veKonvert is not compatible with Victron Chargers and Inverters. It should also not be plugged into the VE.Direct interfaces of any Victron "Consumers" such as Multiplus, Quattro, Cerbo, etc.

Read more less

Artificial HorizonAnswers the need of every sextant user who cannot depend on a natural sea horizon. Use for backyard practice, finding exact positon when inland, and making exact sextant shot on foggy mornings. To use, fill with water and read the angle of the reflected sun with your sextant. Half your sextant reading is the sun's angle above the true horizon. Windproof and corrosion resistant, the reflecting surface is completely enclosed.Comes with two sun shades, a lid and full directions. Compact 6" x 4" x 1-1/2" (15 x 10 x 4 cm). Owner's Manual (pdf)

Read more less

GND™ 10 Black Box BridgeThe Garmin GND 10 black box bridge seamlessly integrates Nexus instruments and sensors with the Garmin family. It converts data between the Nexus network and NMEA 2000 to provide trouble-free compatibility between Nexus and Garmin products including gWind and gWind Race wind transducers. Simple plug-and-play installation between Nexus and NMEA 2000, with USB connectivity eliminates need for user setup and system configuration.GND 10 allows PC applications, such as NexusRace, Expedition, Adrena or SeaTrack, to communicate sailing-specific functions between Nexus and NMEA 2000 networks. It also enables GND 10 software updates over NMEA 2000. Existing NexusRace PC application can be used to update software, configure and calibrate Nexus devices over USB using the FDX protocol.Features: Converts data between the Nexus network and NMEA 2000 Provides trouble-free compatibility between Nexus and Garmin products Simple plug-and-play installation between Nexus, NMEA 2000 and USB No user setup or system configuration required Allows PC applications such as NexusRace, Expedition, Adrena, or SeaTrack, to communicate sailing specific functions between Nexus and NMEA 2000 networks Enables GND 10 software updates over NMEA 2000 Existing NexusRace PC application can be used to update software, configure, and calibrate Nexus devices over USB using the FDX protocol Lighting levels of Nexus Marine instruments can be set from equipment connected to NMEA 2000 Allow setting and resetting of race start timers and distance logs from Garmin equipment connected to the NMEA 2000 network In The Box GND 10 USB Mini-B cable NMEA 2000® drop cable (2 m) NMEA 2000 T-connector Nexus network cable (5 m; straight connector) Mounting hardware Documentation WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

E90W to Axiom Pro 9 Adapter Plate to Existing Fixing Holes Axiom Pro 9 adapter plate for legacy E90W MFDs Fixing holes: Existing Model: Axiom Pro 9 (All variants) Specifications: Type: Mounting Brackets Box Dimensions: 1"H x 13"W x 17"L WT: 1 lbs

Read more less

RCR-SD/USB-Card ReaderRear - Charging, external storage device for Axiom & Axiom Pro Units

Read more less

RayNet(F) to RayNet(F) Port Connectivity - 400mmThe RayNet (F) to RayNet (F) network cable can be used to daisy-chain 2 adjacent RayNet devices together. It is also useful for joining two adjacent HS-5 Network Switches together on larger systems where multiple switches are necessary. This network cable is 15-inches (400mm) long.

Read more less

1.25" BSP Displacement Hull Tank AdapterAdapter from Maretron for displacement hull tanks.WARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

Read more less