Marine Navigation & Instruments - Network Cables & Modules

Fusion to Garmin Marine Network Cable - Male to RJ45 - 6' (1.8M)Use these adapter cables to link your GPSMAP® Series chartplotter to a compatible Fusion® stereo.  These cables will connect a Garmin Marine Network port to an RJ45 port and are offered in male and female connector varieties to fit your specific system.Features: Length - 6' (0.15 M) Connections - RJ45 Compatible Products: Fusion Apollo RA770 Fusion Apollo SRX400 Fusion Apollo WB670 Fusion Apollo RA670 *Sold as an IndividualWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Cable Length (Feet): 6 Box Dimensions: 1"H x 5"W x 6"L WT: 0.25 lbs UPC: 753759288471 Brochure (pdf)

Read more less

M300 Power Serial CVBS Cable - 10MPower/data/video cable for M300C, M332, M364, M364C, and M364C-LR cameras.FLIR Marine camera systems operate on 12V or 24V DC power. To support flexible installations, FLIR offers a variety of replacement and extended-length power cables. Specifications: Cable Length (Feet): 32.8 Box Dimensions: 4"H x 8"W x 11"L WT: 3 lbs UPC: 723193838426

Read more less

Marine Network Cable - 500'Our marine network cable offers an additional 500'(152.4M) of cable length.WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Cable Length (Feet): 500' Box Dimensions: 4"H x 11"W x 11"L WT: 12.8 lbs UPC: 753759049966

Read more less

RJ45 Waterproof ConnectorFLIR's RJ45 waterproof connector is a key component for installing and operating your maritime thermal camera from FLIR. The RJ45 waterproof connector connects the thermal camera itself to the Joystick Control Unit (JCU) using an Ethernet cord, transmitting both data and electricity along a single cord. FLIR has designed the RJ45 waterproof connector with a standard RJ45 port, and it is PoE enabled so you can connect it directly to your JCU without having to use a PoE Injector. It is designed with a sturdy waterproof enclosure to protect against the elements, meaning the connector won't be the weakest link in your thermal imaging chain. You can't control your thermal camera without FLIR's RJ45 waterproof connector.

Read more less

5M LAN Waterproof Cable RJ45 x RJ45 for TZtouchXL Furuno's TZtouchXL LAN Cable ASSYSpecifications: Length: 5M Waterproof RJ45 x RJ45 This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Read more less

GOS™ 10 Hub for Garmin OnBoard™ SystemProtect your passengers and loved ones with the GOS 10 Hub for the Garmin OnBoard system. One of the main components of your Garmin OnBoard system, the GOS 10 Hub communicates wirelessly with the MOB tags and connects to your vessel’s engine harness to provide Engine Cut Off System (ECOS) functionality.What's In The Box? GOS™ 10 Hub for the Garmin OnBoard System 12-pin fused power and engine cut-off harness with external buzzer External antenna for wireless connection to MOB tags NMEA 2000® T-connector NMEA 2000 drop cable Installation hardware Documentation Specifications: Dimensions (HxWxD): 91.55 mm x 155.12 mm x 48.47 mm Weight: 171.7 g Wireless range: 66 ft (up to 20 m) Supply voltage range: 10-32V Operating temperature range: -15 °C to 70 °C Typical power consumption: 50mA @ 12V or 0.6W NMEA 2000 LEN®: 1 Engine compatibility: Inboard, outboard, sterndrive from all major manufacturers Engine interface: Hardwired, in-line connection to ignition harness Number of engines supported: Up to 4 close-to-stop or 2 open-to-stop engines Water rating: IPX6 and IPX7 Compass-safe distance: 5 cm

Read more less

BlueNet™ Network Cable - 500'The Garmin BlueNet™ network cables offer various lengths to help with installations. Various sizes are sold separately. Consider purchasing the Field installable Adapter Kit for the Garmin BlueNet™ network if purchasing this 500-foot-long cable.

Read more less

BlueNet™ Network Cable 8" (Right Angle)The Garmin BlueNet marine network cables offer additional cable lengths to help with installations. Additional sizes sold separately.

Read more less

MPower 12 Channel DC Load Module NMEA 2K with 12" Pigtail Adapter Cable for J1 & J2 ConnectorsDesigned for vessels of all sizes with smaller loads, the MPower® CLMD12 is a compact 12-Channel DC Load Controller Module. Two of the 12 breakers handle a maximum of 12 amps, six handle a maximum of 10 amps, and four handle a maximum of 5 amps, with a total current capacity of 75 Amps. Additionally, circuits can be paralleled.If a smaller circuit needs to be protected, each of the 12 breakers can be set to trip at lower current levels using the new Maretron N2KAnalyzer® V3 software. In addition, the CLMD12 has inputs for up to 7 hard-wired switches that can be used to switch breaker states, or as inputs for other data, such as bilge alarms or hatch positions, etc.The CLMD12 handles many DC load types such as lights, pumps, motors, and electronics. An added benefit of the CLMD12 is that it reports the current through each of the 12 breakers. This allows you to determine if loads are drawing too much or too little electrical current. This information can be used to report overcurrent faults and undercurrent conditions, such as burnt-out bulbs.For manual control of the loads, an optional MPower 12-Channel Bypass Module (CBMD12) can be installed in conjunction with the CLMD12.Features: NMEA 2000® Interface IP67 Rated Ignition Protected Opto-isolated from NMEA 2000®, eliminating potential ground loops Twelve (12) dimmable Electronic Circuit Breakers (ECBs) for On/Off Control over NMEA 2000® network 2 breakers capable of carrying up to 12 Amps 6 breakers capable of carrying up to 10 Amps 4 breakers capable of carrying up to 5 Amps Individual breaker electrical current monitoring Breakers can have Power-Up states defined (ON, OFF, or PREVIOUS STATE) Breakers can be locked against inadvertent actuation. Seven (7) discrete inputs configurable as Active High or Active Low Automatic ECB overcurrent shutdown Automatic ECB thermal shutdown (Overtemperature Protection) Applications: Remote control of navigation lights Remote control of the boarding lights Burnt-out bulb alerts Control of area lights with dimming This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Specifications: AC/DC: DC Touchscreen: No Box Dimensions: 4"H x 7"W x 10"L WT: 2.3 lbs UPC: 873804004181 Quick Guide (pdf)

Read more less

BlueNet™ Network Cable CouplerAttach two Garmin BlueNet™ Network cables with this small and robust coupler.WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

0.5M Jumper Cable for HUB102Furuno's HUB102 0.5M Jumper CableSpecifications: Length: 0.5M Jumper Cable This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Read more less

MPower 12 Channel DC Load Controller Module with NMEA 2K - No ConnectorsDesigned for vessels of all sizes with smaller loads, the MPower® CLMD12 is a compact 12-Channel DC Load Controller Module. Two of the 12 breakers handle a maximum of 12 amps, six handle a maximum of 10 amps, and four handle a maximum of 5 amps, with a total current capacity of 75 Amps. Additionally, circuits can be paralleled.If a smaller circuit needs to be protected, each of the 12 breakers can be set to trip at lower current levels using the new Maretron N2KAnalyzer® V3 software. In addition, the CLMD12 has inputs for up to 7 hard-wired switches that can be used to switch breaker states, or as inputs for other data, such as bilge alarms or hatch positions, etc.The CLMD12 handles many DC load types such as lights, pumps, motors, and electronics. An added benefit of the CLMD12 is that it reports the current through each of the 12 breakers. This allows you to determine if loads are drawing too much or too little electrical current. This information can be used to report overcurrent faults and undercurrent conditions, such as burnt-out bulbs.For manual control of the loads, an optional MPower 12-Channel Bypass Module (CBMD12) can be installed in conjunction with the CLMD12.Features: NMEA 2000® Interface IP67 Rated Ignition Protected Opto-isolated from NMEA 2000®, eliminating potential ground loops Twelve (12) dimmable Electronic Circuit Breakers (ECBs) for On/Off Control over NMEA 2000® network 2 breakers capable of carrying up to 12 Amps 6 breakers capable of carrying up to 10 Amps 4 breakers capable of carrying up to 5 Amps Individual breaker electrical current monitoring Breakers can have Power-Up states defined (ON, OFF, or PREVIOUS STATE) Breakers can be locked against inadvertent actuation. Seven (7) discrete inputs configurable as Active High or Active Low Automatic ECB overcurrent shutdown Automatic ECB thermal shutdown (Overtemperature Protection) Applications: Remote control of navigation lights Remote control of boarding lights Burnt-out bulb alerts Control of area lights with dimming This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Specifications: AC/DC: DC Touchscreen: No Box Dimensions: 4"H x 7"W x 10"L WT: 1.8 lbs UPC: 873804004105 Quick Guide (pdf)

Read more less