Marine Plumbing & Ventilation

Flat Tank Oil Changer SystemThe Jabsco Flat Tank Oil Changer System simplifies the engine oil changing process, ideal for changing engine oil in Boats, RV's, Lawn and Garden Equipment.There is no need to worry about open containers causing spills when changing engine oils with the 3-1/2 Gallon (13LTR) compact self-contained unit fitted with a self-priming diaphragm pump with an easy pour spout for emptying.The Flat Tank design allows for easy storage in deck boxes, boat storage lockers, or RV storage compartments. Easy to use, clean and efficient dipstick suction tube, battery clamp wire leads, an on-off pump switch.Features: Stores easily Compact robust tank design Easy pour spout with screw on cap Easy to carry handle 3-1/2 gallon (13ltr) sealed container Self-priming, run dry pump WARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov. Specifications: Volts: 12v Box Dimensions: 11"H x 12"W x 20"L WT: 8.5 lbs UPC: 671880566803 Owner's Manual (pdf)Brochure (pdf)

Read more less

Rule-Mate 1500 GPH 12 Volt Fully Automated Bilge PumpThe Rule-Mate® 1500 GPH pump consists of a powerful Rule® bilge pump and a highly intelligent circuit board in a single housing. The pump activated when the water reaches 2-1/2" and automatically shuts off when the pump senses no water against the impeller, reducing the remaining water to approximately 5/8". tttRule-Mate IntelligenceRule-Mate Bilge pumps have built-in programming that can sense when the pump is running but not pumping water. This is a very unique feature to bilge pumps because it protects the pump and the vessel, especially the vessels batteries. If debris fouls the sensor or the pump becomes air-bound, the pump will stop running and begin to "check" for water every 2-1/2 minutes. Once the debris is removed, the pump will revert to its normal operation, turning on when the water reaches 2-1/2" and shutting off at 5/8". 1500 GPH (6819 LPH) at 0' (13.6V) All-in-one pump and switch Extra long life heavy duty motor 1" NPS discharge with 1" AND 1 1/8" screw-on ports Three year warranty WARNING: This product can expose you to chemicals including FORMALDEHYDE (GAS) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov. Specifications: Volts: 12v Operation: Automatic Gallons Per Minute: 25 GPM Gallons Per Hour: 1500 GPH Type: Electric Box Dimensions: 5"H x 7"W x 8"L WT: 4.3 lbs UPC: 042237114198 Owner's Manual (pdf)

Read more less

Rule-Mate 2000 GPH 24 Volt Fully Automated Bilge PumpThe Rule-Mate® 2000 GPH pump consists of a powerful Rule® bilge pump and a highly intelligent circuit board in a single housing. The pump activated when the water reaches 2-1/2" and automatically shuts off when the pump senses no water against the impeller, reducing the remaining water to approximately 5/8". ttRule-Mate IntelligenceRule-Mate Bilge pumps have built-in programming that can sense when the pump is running but not pumping water. This is a very unique feature to bilge pumps because it protects the pump and the vessel, especially the vessels batteries. If debris fouls the sensor or the pump becomes air-bound, the pump will stop running and begin to "check" for water every 2-1/2 minutes. Once the debris is removed, the pump will revert to its normal operation, turning on when the water reaches 2-1/2" and shutting off at 5/8". 2000 GPH (7570 LPH) at 0' (27.2V) All-in-one pump and switch Extra long life heavy duty motor 1" NPS discharge with 1" AND 1 1/8" screw-on ports Three year warranty WARNING: This product can expose you to chemicals including FORMALDEHYDE (GAS) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov. Specifications: Volts: 24v Operation: Automatic Gallons Per Minute: 33.3 GPM Gallons Per Hour: 2000 GPH Type: Electric Box Dimensions: 5"H x 7"W x 8"L WT: 4.35 lbs UPC: 042237114303 Owner's Manual (pdf)

Read more less

Rule-Mate 2000 GPH 12 Volt Fully Automated Bilge PumpThe Rule-Mate® 2000 GPH pump consists of a powerful Rule® bilge pump and a highly intelligent circuit board in a single housing. The pump activated when the water reaches 2-1/2" and automatically shuts off when the pump senses no water against the impeller, reducing the remaining water to approximately 5/8". ttRule-Mate IntelligenceRule-Mate Bilge pumps have built-in programming that can sense when the pump is running but not pumping water. This is a very unique feature to bilge pumps because it protects the pump and the vessel, especially the vessels batteries. If debris fouls the sensor or the pump becomes air-bound, the pump will stop running and begin to "check" for water every 2-1/2 minutes. Once the debris is removed, the pump will revert to its normal operation, turning on when the water reaches 2-1/2" and shutting off at 5/8". 2000 GPH (7570 LPH) at 0' (13.6V) All-in-one pump and switch Extra long life heavy duty motor 1" NPS discharge with 1" AND 1 1/8" screw-on ports Three year warranty WARNING: This product can expose you to chemicals including FORMALDEHYDE (GAS) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov. Specifications: Volts: 12v Operation: Automatic Gallons Per Minute: 33.3 GPM Gallons Per Hour: 2000 GPH Type: Electric Box Dimensions: 5"H x 7"W x 8"L WT: 4.3 lbs UPC: 042237114297 Owner's Manual (pdf)

Read more less

Service KitJabsco Service Kit is for Manual 29090 and 29120 Series Toilets from 1998-2007.WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Type: Service Kits Box Dimensions: 3"H x 6"W x 7"L WT: 0.4 lbs UPC: 671880524131

Read more less

Gas Tank Vent Chrome Plated Zinc Alloy with Black Polymer Splash Guard Removable 30 Mesh Stainless Steel Wire Screen Flame Arrestor - for use with fuel applications Hose Size: 5/8" Max Hull Thickness: 3/4"

Read more less

Flush Pro Valve Kit - 5/8"Finally! Freshwater flushing of your inboard is as simple as connecting a garden hose.Features: Polymer Stainless Steel Spring Flush your boat engine safely and easily Transparent body allows for visual inspection of water flow Durable check valve system activated by water pressure from a garden hose Check valve automatically shuts off hull intake when water pressure is applied Adapter supplied with Flush Pro make winterizing your boat easy Can be used with on board generators Available for Standard 5/8" Hose Sizes Kit Includes:Water Inlet Fitting (Part #0499) Owner's Manual (pdf)

Read more less

115V AC MaceratorThe Jabsco AC macerator pump unit is the ideal answer to waste handling problems for marine, recreational vehicle and domestic uses. The macerator section grinds waste down to a particle size of 1/8" maximum so it can be pumped easily through a 1" hose discharge line. The pump is self-priming, permitting the unit to be mounted above or below the tank in a convenient location. For optimal efficiency, locate pump as close to the waste source as practical. Empties a 30 gallon holding tank in only 3 minutes. The waste pump will macerate and pump all waste and tissue normally found in marine waste systems. IT WILL NOT HANDLE HARD SOLID OBJECTS, SANITARY NAPKINS OR RAGS.SpecificationsImpellertNitrileMaceratortCast Bronze Cutter Plate reducesparticle size to 1/8" maximumSealtLip TypePort TypetInlet - 1-1/2" External Pipe ThreadOutlet - 1" ID Hose BarbMotort115 Vac, AC Induction TypeSingle Phase, 60 HzThermal Overload ProtectionWeightt7.7 (kg) 17 (lb)WARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov. Specifications: Gallons Per Minute: 10 GPM Outlet Size: 1" Volts: 115v Type: Waste Pumps Box Dimensions: 9"H x 10"W x 17"L WT: 19.45 lbs UPC: 671880015530 Owner's Manual (pdf)

Read more less

Fish Box Evacuation PumpThe fish box evacuation pump is perfect for emptying a fishbox after a day's fishing. Typically the fish box is not only used for storing the days catch but very often is used for a cooler for supplies. This means that there can be all manner of debris left in the bottom of the fish box at the end of the day. This self-priming pump is designed for passing typical debris, such as bait residue, particles of ice, fish scales, etc. Its dry-running capabilities and the 360° rotatable head allow this pump to be mounted in almost any position in the boat, allowing for total flexibility.Features: Flexible installation No filter required Compact and simple design 12V Dry running capapbility Connections for 38mm (1-1/2") Ports Up to 19 Liters per Minute (5 US Gallons) flow Relevant standards: ISO 8846 MARINE and USCG Regulations for Ignition Protection Meets BSEN 50081 (Electro Magnetic Compatibility) WARNING: This product can expose you to chemicals including FORMALDEHYDE (GAS) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov. Specifications: Outlet Size: 1-1/2" Gallons Per Minute: 5 GPM Volts: 12v Type: Electric Box Dimensions: 6"H x 8"W x 14"L WT: 6.8 lbs UPC: 671880575911 Brochure (pdf)

Read more less

Flush Pro Valve Kit - 1"Finally! Fresh flushing of your inboard is as simple as connecting a garden hose.Features: Polymer Stainless Steel Spring Flush your boat engine safely and easily Transparent body allows for visual inspection of water flow Durable check valve system activated by water pressure from a garden hose Check valve automatically shuts off hull intake when water pressure is applied Adapter supplied with Flush Pro make winterizing your boat easy Can be used with on board generators Available for Standard 1" Hose Sizes Kit Includes:Water Inlet Fitting (Part #0499) Owner's Manual (pdf)

Read more less

Impeller KitMaterial:NeopreneDrive Type:Slotted Shaft - Pin DriveNumber of Blades:6Dimensions: Diameter:1-9/16" Shaft Width:15/32" Shaft Diameter:3/4" Insert Material:BrassJabsco flexible impellers can be fitted to most makes and models of bronze flexible impeller engine cooling, bilge, transfer and general purpose pumps.Jabsco flexible impellers are subjected to rigorous quality processes to ensure reliable, efficient and long lasting performance.Replace all impellers at least once every year, or sooner, depending on the engine duty. When the installation is correct an impeller may last for several years, but it is always advisable to stick to a schedule of preventative, rather than corrective, maintenance.Replacing impellers is easy. By removing the end cover screws, it is possible to remove the impeller by using either a Jabsco Impeller Removal Tool, or channel lock pliers, to grip the hub of the impeller. Don?t use screwdrivers as they may damage the face of the pump body, causing leaks, and they can be dangerous in confined spaces.Always carry spare impellers on board in case of emergency. The impeller is one of the most vital components of the engine cooling system and should always be treated as such. Always grease new impellers. Firstly, it makes it easier to install the impeller into the pump bore, and secondly it gives added protection to the impeller during initial prime. After replacing the gasket and end cover the pump is ready to use.WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Impeller KitMaterial:NeopreneDrive Type:Double Flat DriveNumber of Blades:12Dimensions: Diameter:3-3/4" Shaft Width:1" Shaft Diameter:3-9/16" Insert Material:PlasticJabsco flexible impellers can be fitted to most makes and models of bronze flexible impeller engine cooling, bilge, transfer and general purpose pumps.Jabsco flexible impellers are subjected to rigorous quality processes to ensure reliable, efficient and long lasting performance.Replace all impellers at least once every year, or sooner, depending on the engine duty. When the installation is correct an impeller may last for several years, but it is always advisable to stick to a schedule of preventative, rather than corrective, maintenance.Replacing impellers is easy. By removing the end cover screws, it is possible to remove the impeller by using either a Jabsco Impeller Removal Tool, or channel lock pliers, to grip the hub of the impeller. Don?t use screwdrivers as they may damage the face of the pump body, causing leaks, and they can be dangerous in confined spaces.Always carry spare impellers on board in case of emergency. The impeller is one of the most vital components of the engine cooling system and should always be treated as such. Always grease new impellers. Firstly, it makes it easier to install the impeller into the pump bore, and secondly it gives added protection to the impeller during initial prime. After replacing the gasket and end cover the pump is ready to use.WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less