Marine Plumbing & Ventilation

Impeller KitMaterial:NeopreneDrive Type:Spline DriveNumber of Blades:12Dimensions: Diameter:2-1/4" Shaft Width:5/8" Shaft Diameter:1-29/32"Insert Material:BrassJabsco flexible impellers can be fitted to most makes and models of bronze flexible impeller engine cooling, bilge, transfer and general purpose pumps.Jabsco flexible impellers are subjected to rigorous quality processes to ensure reliable, efficient and long lasting performance.Replace all impellers at least once every year, or sooner, depending on the engine duty. When the installation is correct an impeller may last for several years, but it is always advisable to stick to a schedule of preventative, rather than corrective, maintenance.Replacing impellers is easy. By removing the end cover screws, it is possible to remove the impeller by using either a Jabsco Impeller Removal Tool, or channel lock pliers, to grip the hub of the impeller. Don?t use screwdrivers as they may damage the face of the pump body, causing leaks, and they can be dangerous in confined spaces.Always carry spare impellers on board in case of emergency. The impeller is one of the most vital components of the engine cooling system and should always be treated as such. Always grease new impellers. Firstly, it makes it easier to install the impeller into the pump bore, and secondly it gives added protection to the impeller during initial prime. After replacing the gasket and end cover the pump is ready to use.WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Impeller KitMaterial:NitrileDrive Type:Single Flat DriveNumber of Blades:10Dimensions: Diameter:1-19/32" Shaft Width:5/16" Shaft Diameter:3/4" Insert Material:BrassJabsco flexible impellers can be fitted to most makes and models of bronze flexible impeller engine cooling, bilge, transfer and general purpose pumps.Jabsco flexible impellers are subjected to rigorous quality processes to ensure reliable, efficient and long lasting performance.Replace all impellers at least once every year, or sooner, depending on the engine duty. When the installation is correct an impeller may last for several years, but it is always advisable to stick to a schedule of preventative, rather than corrective, maintenance.Replacing impellers is easy. By removing the end cover screws, it is possible to remove the impeller by using either a Jabsco Impeller Removal Tool, or channel lock pliers, to grip the hub of the impeller. Don?t use screwdrivers as they may damage the face of the pump body, causing leaks, and they can be dangerous in confined spaces.Always carry spare impellers on board in case of emergency. The impeller is one of the most vital components of the engine cooling system and should always be treated as such. Always grease new impellers. Firstly, it makes it easier to install the impeller into the pump bore, and secondly it gives added protection to the impeller during initial prime. After replacing the gasket and end cover the pump is ready to use.WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Impeller Kit - 8 Blade - Neoprene - 2-9/16" Diameter x 3" W, 5/8" Shaft DiameterFeatures: Material: Neoprene Drive Type: Spline Drive Number of Blades: 8 Dimensions: Diameter: 2-9/16", Shaft Width: 3", Shaft Diameter: 5/8" Insert Material: Brass Jabsco flexible impellers can be fitted to most makes and models of bronze flexible impeller engine cooling, bilge, transfer and general purpose pumps.Jabsco flexible impellers are subjected to rigorous quality processes to ensure reliable, efficient and long lasting performance.Replace all impellers at least once every year, or sooner, depending on the engine duty. When the installation is correct an impeller may last for several years, but it is always advisable to stick to a schedule of preventative, rather than corrective, maintenance.Replacing impellers is easy. By removing the end cover screws, it is possible to remove the impeller by using either a Jabsco Impeller Removal Tool, or channel lock pliers, to grip the hub of the impeller. Don?t use screwdrivers as they may damage the face of the pump body, causing leaks, and they can be dangerous in confined spaces.Always carry spare impellers on board in case of emergency. The impeller is one of the most vital components of the engine cooling system and should always be treated as such. Always grease new impellers. Firstly, it makes it easier to install the impeller into the pump bore, and secondly it gives added protection to the impeller during initial prime. After replacing the gasket and end cover the pump is ready to use.WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Impeller Kit - 9 Blade - Nitrile - 3-3/4" Diameter x 3-1/2" W, 1" Shaft DiameterFeatures: Material: Nitrile Drive Type: Spline Drive Number of Blades: 9 Dimensions: Diameter: 3-3/4", Shaft Diameter: 1", Shaft Width: 3-1/2" Jabsco flexible impellers can be fitted to most makes and models of bronze flexible impeller engine cooling, bilge, transfer and general purpose pumps.Jabsco flexible impellers are subjected to rigorous quality processes to ensure reliable, efficient and long lasting performance.Replace all impellers at least once every year, or sooner, depending on the engine duty. When the installation is correct an impeller may last for several years, but it is always advisable to stick to a schedule of preventative, rather than corrective, maintenance.Replacing impellers is easy. By removing the end cover screws, it is possible to remove the impeller by using either a Jabsco Impeller Removal Tool, or channel lock pliers, to grip the hub of the impeller. Don?t use screwdrivers as they may damage the face of the pump body, causing leaks, and they can be dangerous in confined spaces.Always carry spare impellers on board in case of emergency. The impeller is one of the most vital components of the engine cooling system and should always be treated as such. Always grease new impellers. Firstly, it makes it easier to install the impeller into the pump bore, and secondly it gives added protection to the impeller during initial prime. After replacing the gasket and end cover the pump is ready to use.WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Owner's Manual (pdf)

Read more less

Impeller KitMaterial:NeopreneDrive Type:Spline DriveNumber of Blades:10Dimensions: Diameter:2-9/16" Shaft Width:⅝" Shaft Diameter:2" Insert Material:BrassJabsco flexible impellers can be fitted to most makes and models of bronze flexible impeller engine cooling, bilge, transfer and general purpose pumps.Jabsco flexible impellers are subjected to rigorous quality processes to ensure reliable, efficient and long lasting performance.Replace all impellers at least once every year, or sooner, depending on the engine duty. When the installation is correct an impeller may last for several years, but it is always advisable to stick to a schedule of preventative, rather than corrective, maintenance.Replacing impellers is easy. By removing the end cover screws, it is possible to remove the impeller by using either a Jabsco Impeller Removal Tool, or channel lock pliers, to grip the hub of the impeller. Don?t use screwdrivers as they may damage the face of the pump body, causing leaks, and they can be dangerous in confined spaces.Always carry spare impellers on board in case of emergency. The impeller is one of the most vital components of the engine cooling system and should always be treated as such. Always grease new impellers. Firstly, it makes it easier to install the impeller into the pump bore, and secondly it gives added protection to the impeller during initial prime. After replacing the gasket and end cover the pump is ready to use.WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Flush Mount Hose AdapterPerfect solution to remove that unsightly hose bib deck fitting and rusty knob. This will enable you to connect your water hose in seconds.Enables you to quick-connect your water hose in seconds. Position this fitting close to your anchor windlass to clean muddy anchors, or locate one on each side of your vessel to make cleanups much easier. Combine the deck washdown fitting with a hose coil washdown hose and keep the deck clutter free.Features: Extra 3/4" GHT male hose adaptor suitable for HoseCoil Water flow available with an easy twist of the fitting Easy to install Position this fitting close to your anchor windlass to clean those muddy anchors. Or locate one on each side of your vessel to make those cleanups much easier Just combine the Quick Release Deck Washdown fitting with a Hose Coil Washdown hose and a high volume Jabsco PAR-Max 4 Washdown pump to keep the deck clutter free Comes with a pre-installed check valve that connects your hose with a simple twist to the deck fitting, even under full pressure Specifications: Type: Tools & Accessories Box Dimensions: 2"H x 8"W x 8"L WT: 0.3 lbs UPC: 671880550253

Read more less

iL200 Plus In-Line & Submersible Pump 12VCentrifugal submersible and inline pump; Suitable for diesel, fresh and salt water Quick diesel transfer with no spillage Bait tank aeration, diesel transfer, water transfer Water Systems to 80°C Continuous rating but should not be run dry for long periods Specifications Output: up to 12.7 litres/minute at up to .75bar (2.8 gallons/minute at 11psi) Connections: 1/2" (12.7mm) Hose Dimensions (L x H): 142 x 38 (mm) Amp Draw: 2.5 (amp) Weight: 260 (g) WARNING: This product can expose you to chemicals including FORMALDEHYDE (GAS) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov. Specifications: Gallons Per Minute: 2.8 GPM Volts: 12v Type: Electric Box Dimensions: 3"H x 9"W x 13"L WT: 1 lbs UPC: 042237109866 Owner's Manual (pdf)

Read more less

Replacement Strainer BaseReplacement Strainer Base f/Rule Mate Bilge Pumps w/FLow Rate 1500-2000gphWARNING: This product can expose you to chemicals including FORMALDEHYDE (GAS) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov. Specifications: Type: Strainers Box Dimensions: 2"H x 8"W x 9"L WT: 0.25 lbs UPC: 042237085955

Read more less

1800 GPH Non-Automatic 110V PumpPart #: A53DA high performance 110 Volt utility pump that is designed to remove water from hard to reach spaces anywhere water accumulates.The pump's versatile design makes it the perfect solution to remove water from basements, garages, stairwells, utility rooms, backyards, sumps, pools, pool covers, boats, and for other utility applications. It features an improved unibody housing that is corrosion proof and reduces potential leak paths. The pump features a powerful 1800 GPH motor that only consumes 100 watts, while delivering up to 1800 gallons per hour.Applications:The Rule line of 1800 GPH utility pumps are ideally suited for removing unwanted water from basements, garages, backyards and boats and has a robust motor, a sturdy housing and a rugged impeller for years of pumping power.WARNING: This product can expose you to chemicals including BISPHENOL A (BPA) which is known to the State of California to cause birth defects or other reproductive harm, and Diisononyl Phthalate (DINP) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov. Specifications: Gallons Per Hour: 1800 GPH Operation: Non-Automatic Outlet Size: 1-1/8" Volts: 110v Type: Electric Box Dimensions: 7"H x 8"W x 11"L WT: 4.7 lbs UPC: 042237083463 Owner's Manual (pdf)Brochure (pdf)

Read more less

JABSCO WATER PRESSURE REGULATORFLUSH MOUNT MODEL 44411-SERIESDesigned for day and night protection of the entire plumbing system fromunregulated city water system hook-ups. Whether connected to a dock-sidemain or a campground faucet, the new Jabsco Regulator will maintain regulatedoutput at low or high flow rates. The removable strainer protectsvalves and seal-seats from pipe scale and other debris.FEATURES Reduces unregulated city water pressures that can runas high as 125 psi down to a safe 45 psi - automatically Features built-in backflow preventer. Federal and Staterequired on RV's with water service hookup Flush mounts permanently in vessel super structure Easily replaces most original city water entries Automatic pressure regulation Built-in backflow preventer Easy cleaning strainer Dust cap WARNING: This product can expose you to chemicals including STYRENE which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov. Owner's Manual (pdf)Brochure (pdf)

Read more less

Par-Max Shower Drain/General Purpose Pump - 3.5GPM-25psi-12VDC with StrainerLong-life fully serviceable shower drain pump.Features: 3.5 GPM (13.2 lpm) at 3ft (1m) head Self-priming up to 10ft (3m) allows mounting above wet bilges Diaphragm design allows extended dry running Continuous rated, heavy duty motor sealed for harsh bilge environments Thermal overload protection automatically stops the motor if it overheats due to overloading, with an auto re-start feature Complies with USCG 183.410 and ISO 8846 MARINE (Ignition Protection) ISO 8849 MARINE (Bilge Pump Standard) Complete with Pumpgard Oil resistant elastomers Fitting: Connections for 3/4" (19mm ) ID hose Size: 7.7" long x 4.2" wide x 4.1" high (19.6cm x 10.6cm x 10cm) Weight: 5.0lb (2.1kg) WARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov. Specifications: Gallons Per Minute: 3.5 GPM Max PSI: 25 Volts: 12v Box Dimensions: 5"H x 7"W x 13"L WT: 6.5 lbs UPC: 671880595667 Owner's Manual (pdf)

Read more less

Engine Cooling Pump - Flange Mount - 1-1/4" PumpFlow rate: 14 gallons/min at 1500 rpmSelf priming from dry up to 2.4 m (7.8ft)Features: Constructed from marine quality bronze and stainless steel for ruggedness and reliability Easy to service and maintain Body: Bronze Impeller: Neoprene Wearplate: Not fitted Shaft: 316 Stainless Steel Bearings: Single row, ball type Port Type: 1-1/4" Hose Barb Weight: 5 lb WARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer, and LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Owner's Manual (pdf)

Read more less