Products

Voyager Electric Compact Toilet System with Tank - 12VA complete sanitation system is designed for small compartment systems where tanks cannot be installed. Does not need a pressurized water system. Just needs a water hookup.Features: Utilizes a suction pump on the toilet 8-gallon tank 1-button flush and fill Low profile allows for ample headroom All ceramic bowl Compact design, compact seats Specifications:Dimensions: 19" x 21" x 20-1/2" Brochure (pdf)

Read more less

Voyager Manual Toilet System with TankComplete sanitation system designed for small compartment systems where tanks cannot be installed. Does not need a pressurized water system. Just needs a water hookup.Features: Does not require electricity Hand pump to utilize water and flush 8-gallon tank Discharge fitting for easy pump out to a deck fitting Utilizes proven marine toilets Specifications:Dimensions: 19" x 17" x 18-1/2" Brochure (pdf)

Read more less

2-Bank Battery Isolator, 200A, 40VAnalytic Systems introduces the IBI (Ideal Battery Isolator) for 1, 2 and 3 bank battery systems, allowing all the batteries to be fully charged from a single alternator while maintaining electricalisolation between the battery banks or between a vehicle and trailer.Ideal Diode technology uses MosFet Transistors and control circuitry to replace the diode used in a traditional battery isolator and reduces the voltage drop across the isolator to a mere 160 millivolts at 200 Amps of charging current and essentially zero volts at low current, so all the power of the alternator is applied to the batteries ensuring a full recharge every time.While the Ideal Battery Isolator is designed to be used with an alternator, it can also be used to convert a single bank battery charger to a 2 or 3 bank charger or as a pure diode between a vehicle and trailer or other remote load.Features: Waterproof Expoxy Sealed Construction Easy Connection Alternator/Charger post 5/16", Battery Post 1/4" Most Efficient use of Available Alternator Output Maximize Battery Performance Three year parts and labour warranty

Read more less

AC Charger 1-Bank 100A 12V Out/110/220V InAC Chargers are available as two-stage or two and three-stage chargers capable of charging one or two banks of 12, 16, 24, 28, 32, 36, 48, 72V (rail) or other voltage battery banks, and are designed to quickly and accurately charge and condition batteries.

Read more less

AC Charger 2-Bank 40A, 24V Out, 110VAC In CSA/ULThis BCA1000 COTS AC-source battery charger is designed to charge a battery at 24VDC.Internally, the single-board design incorporates a time-tested switch mode technology for unmatched efficiency and ultra-quiet operation. Additional stages of filtering on the outputs reduce conducted and radiated EMI noise to very low levels.This unit features a user-selectable 2-stage or 3-stage charging profile, and the output voltage adjusts for optimum charging. Additionally, the equalization mode and voltage temperature compensation increase the lifetime of expensive battery systems.Built for rugged duty, this unit is constructed from heavy-duty anodized extruded and billet machined aluminum with O-ring seals and all stainless-steel fasteners.Reliability features of this product line include LED status indicators, over-temperature shutdown, current limiting, reverse polarity battery connection protection, output short circuit shutdown with automatic recovery, and output over-voltage protection.Features: Adjustable charging voltage Single or two-bank charging Ultra-quiet low EMI operation Bright LED indicators Equalize mode functionality Rugged and reliable Specifications:Input: Nominal Voltage: 110 VAC  Actual Voltage: 90-133 VAC Frequency: 45-65 Input Amps (Max): 13 A  Input Fuse (Slow blow): MDA-20 Output: Nominal Voltage: 24 VDC Float Voltage: 27.2 VDC Absorption Voltage: 28.8 VDC Charging Amps: 40 A  Output Fuses (parallel): 2x ATC-30  Absorption to Float Switch: 6 Amps Output Overvoltage Protection: 32 ± 1V  Temperature Compensation: -60mV/°C  Equalize Voltage: 31.0 VDC  Recommended Battery Size (Amp-hours): 160-240  Supported no. of Battery Banks: Charges up to two connected battery banks Output Volt. Adjust: +/- 1.0 V Charging Stages (Selectable): 2 Stage (CC-Float) or 3 Stage (CC-Absorption-Float), User-selectable Output Ripple & Noise: <50 mV Transient Response: <1V for 50% Surge Regulation (Line & Load): < +/- 0.5% Duty Cycle: Continuous (100% for 24 hours per day) Efficiency: >75% @ Maximum Output Mechanical: Length: 14.5 in. / 36.8 cm Width: 9.9 in. / 25.1 cm Height: 5.0 in. / 12.7 cm Clearance: 1.0 in. / 2.5 cm all around Weight: 12.0 lb. / 5.5 kg (approximate) Material and Finish: Black anodized marine-grade aluminum Fasteners: 18-8 stainless steel Input Connection: 3 m / 9.8ft 3xAWG14 power cord with NEMA 5-15 or CEE 7/VII compatible plug Output Connection: Molex 4-pin BEAU Terminal Strip Battery Temperature Sensor Connection: RJ45 ‘telephone jack’ connector Environmental & Safety: Operating Temperature: -25°C to +40°C @ maximum output. Derate linearly 2.5% per °C from +40°C Storage Temperature: -40°C to +100°C Humidity: 0 - 95% relative humidity (non-condensing) with standard conformal coating Isolation: Input-Output & Input-Case: 1500 VDC; Output-Case: 500 VDC (1500 VDC @ 48 V Out) Cooling: Two interior thermostatic cooling fans Audible Noise: 0 dB @ 1 meter when the fan operating Typical Service Life: > 10 years (87,600 hrs.) Warranty: Three Years of Parts and Labor Safety: Designed to meet UL458 & CSA 22.2.107.1 This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Specifications: Charging Banks: 2 Box Dimensions: 7"H x 12"W x 16"L WT: 12.6 lbs Brochure (pdf)

Read more less