Boat Outfitting - Fuel Systems

316 Stainless Steel Alloy Flush Mount Fuel Vent - 90° VentOn the exterior, they have a smooth edge over the competition. Unlike some others, there is no protruding cap to cause damage or be damaged by hull bumps and scrapes. Cap unscrews with a hex head wrench for easy cleaning of the filter and pressure testing of the entire fuel system. These vents now include two silicone gaskets.Features:90-degree ventSpecifications: Hose Size (inch): 5/8" inner diameter Maximum Hull Thickness (inch): 7/8" Installation Hole Size (inch): 1-3/8" *Includes two silicone gaskets Quick Guide (pdf)

Read more less

Deck Fill for Pressure Relief Systems - Angled Body & Scalloped Stainless Steel CapPressure relief systems are designed with automatic diurnal emission control and overpressure relief safety valves built into the cap of the fill. The overpressure relief safety valves are engineered to release pressure above 1 psi. The high-flow vacuum valves allow fresh air to enter the fuel tank to replace the fuel being consumed by the engine. Other components of a pressure relief system are designed to ensure the tank fills to the proper level every time without spit-back or well-back. All Attwood pressure relief systems are designed to ensure water does not enter the fuel tank and are compatible with Jerry Can and marine nozzle refueling.Features: Fits 1-1/2 (inch) fill hose and 5/8 (inch) vent hose Triple high-flow vacuum valves ensure maximum make-up airflow (compatible with high HP applications) Dual 1 psi diurnal emission control and overpressure relief safety valves built into the cap Automatic nozzle shutoff 4-18 gpm Stainless Steel finish An essential component of VaporTec and SecureStop Designed and tested to prevent water from entering the fuel system EPA / CARB Certified Hinged audible click cap meets EPA requirements Meets CARB 13 CCR 2235 and ISO 13331 nozzle mating and retention standards *Compatible with Ethanol blended fuels Quick Guide (pdf)

Read more less

Fuel/Oil Mixing BottleAllows the addition of the exact amount of oil required for a 2-cycle engine. Oil level marks are in gallons and liters. Determines ratios for 100:1, 50:1, 24:1 and 10:1 mixes. Wide mouth, quart-size bottle.Features: Markings to mix oil for 2 Cycle engine Convenient wide-mouth, quart-size bottle Clear oil level marks in black Quick Guide (pdf)

Read more less

1-1/4" x 50' Coil Flex Marine Wet Exhaust & Water Hose - BlackTrident Flex wet exhaust hose for longer bent connections. In smaller I.D.'s for engine intake, critical water, drain, scupper bilge & sanitation uses. Resists heat, ozone, exhaust, panting, and collapse. Black High Temp EDPM Rubber 250°F (121°C) Max.Features:  Extra heavy tube and cover with wire helix between 2 ply reinforcement provides excellent flexibility and bend radius  Resists heat, ozone, exhaust, sani chemicals, panting and collapse Exceeds SAE J2006-R2, ABYC & NMMA P-1 exhaust standards, and Lloyd’s Registry Type Approved Application: Trident Flex wet exhaust hose for longer bent connections In smaller I.D.’s for engine intake, critical water, drain, scupper bilge & sanitation uses Construction: Tube & Cover: High temp EDPM rubber Color: Black with blue stripe Reinforcement: Multi-ply, high-tenacity polyester, steel helix Temperature Range: 250°F (121°C) Length: 50’ (15.24m) Specifications: Inner Diameter: (inch) 1-1/4" / (mm) 31.8 Outer Diameter: (inch) 1.40" / (mm) 32 Working Pressure: (Psi) 70 / (bar) 4.8 Bend Radius: (inch) 1.5" / (mm) 38 Weight: (Lb./50ft.) 35 / (Kg/m) 15.7 *Burst Pressure is 4 x Working Pressure Quick Guide (pdf)

Read more less

3/8" Low Permeation Type A1-15 Fuel Line Hose - Black - Sold by the FootTrident Barrier Lined A1-15 Fuel Hose for both gasoline (including ethanol blends up to 85%) and diesel (including bio diesel blends up to B100). This hose is built with the best fuel, fire, and age-resistant formulation, and a unique "Barrier Liner" on the inside surface of the tube, so fuel is not in direct contact with rubber.Features:  Sold by the foot Provides extraordinary resistance to fuel permeation, aging, and also to fire, heat, cold, and the ozone  Also provides excellent bend-ability NMMA Type Accepted & CE certified Applications: Marine Fuel Hose (distribution, return, vent and transfer) For all marine fuels including gasoline, alcohol blends (CE-10), diesel and bio-diesel Construction: Tube: Nylon Internal Barrier, NBR  Cover: NBR/PVC Blend  Reinforcement: Polyester 2 spiral  Temperature Range: -20°F to 212°F (-28ºC to 100ºC) Specifications: Inner Diameter: (inch) 3/8" / (mm) 9.50 Outer Diameter: (inch) 0.681 / (mm) 17.3 Burst Pressure: (psi) 400 / (mpa) 2.76 Working Pressure: (psi) 100 / (mpa) 0.69 Bend Radius: (inch) 2" / (mm) 50.8 Weight: (lb/100 ft.) 15.6 / (kg/m) 0.233 Permeation Rate: <10 (Standard is 10g/m2/24 hrs (CE10) *The #365 series exceeds ABYC H-24 & H-33, SAE J1527, ISO 7840, USCG Type A1-15; CARB Executive Order RM-17-008 and EPA Certified low permeation Type A1-10This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Specifications: ID Diameter (inches): 3/8" Length (Feet): Sold By The Foot Box Dimensions: 1"H x 1"W x 1"L WT: 0.17 lbs Quick Guide (pdf)

Read more less

5/8" x 50' Boxed Type A2 Fuel & Vent Line Hose - BlackTrident 5/8” A2 Fuel Hose for gasoline vent hose (including ethanol blends) and diesel (including bio diesel blends). This hose is built with the best fuel, fire and age resistant formulation.Features: Provides extraordinary resistance to aging, fire, heat, cold, and the ozone  Also provides excellent bend-ability NMMA Type Accepted & CE certified Application: Fuel Hose for vent and diesel distribution  For all marine fuels including gasoline, alcohol blends, diesel and bio-diesel Construction: Tube: Nylon Internal Barrier, NBR  Cover: NBR/PVC Blend  Reinforcement: Polyester 2 spiral  Temperature Range: -20°F to 212°F (-28ºC to 100ºC)  Length: 50 ft. (15 m) Boxed Specifications: Inner Diameter: (inch) 5/8" / (mm) 15.9 Outer Diameter: (inch) 0.960 / (mm) 24.4 Burst Pressure: (psi) 200 / (mpa) 1.38 Working Pressure: (psi) 50 / (mpa) 0.34 Bend Radius: (inch) 3" / (mm) 76.2 Weight: (lb/100 ft.) 25.84 / (kg/m) 11.72 *The #317 series exceeds ABYC H-24 & H-33, SAE J1527, ISO 7840, & USCG Type A2 Quick Guide (pdf)

Read more less

6" ID 90-Degree EPDM Black Rubber Molded Wet Exhaust Elbow with 4 T-Bolt ClampsTrident EPDM marine wet exhaust connections are molded of high-temperature black EPDM rubber with a smooth bore and cover; except elbows of 6” I.D. or bigger have molded reinforcing ribs on the outside.Features: Four stainless steel clamps are included This elbow has excellent resistance to ozone, salt water, diesel fumes and splashes, cold, heat, and aging Exceeds (SAE J2006-R1, and ABYC & NMMA P-1 exhaust standards) Black high-temp EDPM rubber Construction: Color: Black Reinforcement: Reinforcing ribs on 6” I.D. and above Temperature Range: up to 250°F (121°C) Specifications: Inner Diameter: (inch) 6” / (mm) 152.4 A: (inch) 7" / (mm) 178 B: (inch) 7” / (mm) 178 C: (inch) 2.25” / (mm) 57 D: (inch) 2.25” / (mm) 57 R: (inch) 1.75” / (mm) 44.4 W: (inch) 0.25” / (mm) 6.4 Elbow Degree: 90 degrees Quick Guide (pdf)

Read more less

4' Black Stern Flex Hose with Transom FlangeThis Trident Stern Flex Hose is black (Trident Marine 129 series) and contains wire, control cables, and hoses between the transom and outboard engine(s). Connects to Trident flange part #142-2000.Features: Highly resistant to crushing, abrasion, and UV and has excellent resistance to chemicals  Extraordinary flexibility Construction: Hose: Lightweight polyethylene copolymer Reinforcement: Integral Polyethylene Helix Temperature Range: -40°F to 140°F (-40ºC to 60ºC) Specifications: Color: Black Inner Diameter: (inch) 2” / (mm) 50.8 Outer Diameter: (inch) 2.35” / (mm) 60 Bend Radius: (inch) 3.5” / (mm) 88.9 Weight: (lb/100 ft.) 26 / (kg/m) 11.8 Quick Guide (pdf)

Read more less

1-1/4" Flex Marine Wet Exhaust & Water Hose - Black - Sold by the FootTrident Flex wet exhaust hose for longer bent connections. In smaller i.d.s for engine intake, critical water, drain, scupper bilge & sanitation uses. Resists heat, ozone, exhaust, panting, and collapse. Black High Temp EDPM Rubber 250°F (121°C) Max.Features:  Sold by the foot Extra heavy tube and cover with wire helix between 2-ply reinforcement provides excellent flexibility and bend radius  Resists heat, ozone, exhaust, sani chemicals, panting, and collapse Exceeds SAE J2006-R2, ABYC & NMMA P-1 exhaust standards, and Lloyd’s Registry Type Approved Application: Trident Flex wet exhaust hose for longer bent connections In smaller I.D.s for engine intake, critical water, drain, scupper bilge & sanitation uses Construction: Tube & Cover: High temp EDPM rubber Color: Black with blue stripe Reinforcement: Multi-ply, high-tenacity polyester, steel helix Temperature Range: 250°F (121°C) Specifications: Inner Diameter: (inch) 1-1/4" / (mm) 31.8 Outer Diameter: (inch) 1.40" / (mm) 32 Working Pressure: (Psi) 70 / (bar) 4.8 Bend Radius: (inch) 1.5" / (mm) 38 Weight: (Lb./50 ft.) 35 / (Kg/m) 15.7 *Burst Pressure is 4 x Working PressureThis product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Specifications: ID Diameter (inches): 1-1/4" Length (Feet): Sold By The Foot Box Dimensions: 1"H x 1"W x 1"L WT: 0.64 lbs Quick Guide (pdf)

Read more less

Universal Fuel/Water Separator Kit with BracketKeep your engine running at peak efficiency by filtering out any water that may get into the fuel system. 10-micron filtering capability and fits all 2 and 4-cycle engines.Features: 10 Micron Filter and bracket included Outfitted with 2 brass plugs for secure connections and universal 3/8 inch (.85cm) ports Double seal for enhanced performance Replaces Mercury 35-60494A4 Quick Guide (pdf)

Read more less

5/8" Type A2 Fuel & Vent Line Hose - Black - Sold by the FootTrident 5/8” A2 Fuel Hose for gasoline vent hose (including ethanol blends) and diesel (including bio diesel blends). This hose is built with the best fuel, fire and age resistant formulation.Features: Sold by the foot Provides extraordinary resistance to aging, fire, heat, cold, and the ozone  Also provides excellent bend-ability NMMA Type Accepted & CE certified Applications: Fuel Hose for vent and diesel distribution  For all marine fuels including gasoline, alcohol blends, diesel and bio-diesel Construction: Tube: Nylon Internal Barrier, NBR  Cover: NBR/PVC Blend  Reinforcement: Polyester 2 spiral  Temperature Range: -20°F to 212°F (-28ºC to 100ºC) Specifications: Inner Diameter: (inch) 5/8" / (mm) 15.9 Outer Diameter: (inch) 0.960 / (mm) 24.4 Burst Pressure: (psi) 200 / (mpa) 1.38 Working Pressure: (psi) 50 / (mpa) 0.34 Bend Radius: (inch) 3" / (mm) 76.2 Weight: (lb/100 ft.) 25.84 / (kg/m) 11.72 *The #317 series exceeds ABYC H-24 & H-33, SAE J1527, ISO 7840, & USCG Type A2This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Specifications: ID Diameter (inches): 5/8" Length (Feet): Sold By The Foot Box Dimensions: 1"H x 1"W x 1"L WT: 0.27 lbs Quick Guide (pdf)

Read more less

90° P-Trap Fuel Tank Vent - Black with Stainless Steel Trim CoverComposite 90-degree P-trap fuel tank vent 66419-3. These vents help prevent water from entering the fuel tank, yet allow air to vent freely, during normal sea conditions and washdowns.  This eliminates the need for an anti-siphon loop in the vent hose.  Features: For 5/8" I.D. hose (inch) 3/4" install. hole size (inch) 9/16" max. hull thickness Vents air from your boat's fuel tank as you fill the fuel tank Splash-resistant, corrosion resistant Meets ABYC standard *Compatible with Ethanol blended fuels Quick Guide (pdf)

Read more less