Boat Outfitting - Tools

Adhesive Dispensing Gun with 10:1 Plunger for AT-6030 Adhesive OnlyThe AT- 301 Adhesive Dispensing Gun Is Designed Specifically For Use With Our AT-6030 38 ml 10:1 Adhesive Cartridge. This Hand Operated Gun And Our Mixing Tips Provide Precise Mixing And Dispensing Of Our Adhesives. The Mixing Tip Is Easily Replaced Should The Glue Set Up. We Recommend 5 Mixing Tips Per Cartridge Of Adhesive. A 10:1 Adhesive Plunger Is Included With Gun.

Read more less

AT-850 Square Mixing Tip 4" - Case of 50Weld Mount's AT-850 tip is for use only with the 2010, 4010, & 8040 adhesives. It's unique design eliminates any possibility of the cartridge plugging up as the entry is separated.Features: Square Mixing Tip 4" Long Case of 50

Read more less

AT-850 Square Mixing Tip f/2010, 4020, & 8040 Adhesives - 4" - Case of 10Weld Mount's AT-850 tip is for use only with the 2010, 4020, & 8040 adhesives. It's unique design eliminates any possibility of the cartridge plugging up as the entry is separated.Features: Square Mixing Tip 4" Long Case of 10

Read more less

AT-14 1 to 1 Adhesive Gun Plunger for AT-2010, AT-4020 & AT-6030 AdhesivesAT-14 is specifically for Weld Mount AT-2010, AT-4020, and AT-6030 adhesives. (sold separately)

Read more less

Emergency Deck Fill PlugNitrile-Buna RubberThis Emergency Deck Fill Plug is a must for any vessel. Fits most 1-1/2" hose deck fills in the event you lose your cap. For temporary use only until you can replace your OEM cap. Constructed of fuel resistant Nitrile-Buna rubber. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Rigging Knife - 304 Stainless SteelThis handy Rigging Knife includes a sharp blade, Marlin spike, shackle key, screw driver, bottle opener, and a loop to attach a lanyard (not included). Constructed of corrosion resistant 304 stainless steel. A great addition to any tool box. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Add-A-Snap - White - 4" For use with canvas or nylon boat covers, the Add-A-Snap allows you to easily add length on hard to reach snaps from shrunken material. Nickel plated brass/nylon.WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

1.25" Tall Stainless Stud w/#8 x 32 ThreadOur Small Stainless Steel Panel Studs have a wide range of uses. Originally they were used for mounting on the backside of dash panels for mounting to the console. Now they are used for securing a wide range of wire clamps and other small components to composite surfaces. The base plate is 0.62" in diameter with a 1.25" tall stud. Tensile strength is 300 lbs. and shear strength is 375 lbs. Maximum torque load is 45 inch/lbs.

Read more less

8040 Acrylic Adhesive with Plunger AT-8040 is a good general-purpose adhesive packaged in a manual plunger cartridge. Simply snip off the two end caps dispense the needed amount of adhesive onto a clean surface and mix it by hand. AT-8040 cures in 10-12 minutes, has a 6-minute working time and develops working strength in 40 minutes. AT-8040 has a 12-month shelf life when stored at 72°. Weld Mount recommends that wherever possible this adhesive be refrigerated. Packaged in a 30ml cartridge this adhesive does not require the adhesive gun or mixing tips. The 30ml cartridge will bond 30-50 parts. Quick Guide (pdf)Owner's Manual (pdf)

Read more less

1.5" Tall Stainless Stud w/1/4" x 20 ThreadMounts to virtually any surface using the AT-4010 Acrylic Adhesive. This is a structural part with 500 lbs. of tensile strength and 650 lbs. in shear. All studs have 1/4" x 20 threads. Use for hanging panels, through deck mounts and many other uses.

Read more less

1" Tall Stainless Stud w/#8 x 32 ThreadOur Small Stainless Steel Panel Studs have a wide range of uses. Originally they were used for mounting on the backside of dash panels for mounting to the console. Now they are used for securing a wide range of wire clamps and other small components to composite surfaces. The base plate is 0.62" in diameter with a 1" tall stud. Tensile strength is 300 lbs. and shear strength is 375 lbs. Maximum torque load is 45 inch/lbs.

Read more less

Stainless Steel Stud 1.25" Base 10 x 24 Threads 1.00" Tall - 15 QuantityStuds with smaller threaded stud inserted into the base. These studs are ideal for mounting wire clamps and securing items that require a smaller stud diameter. These studs can be bonded from either surface of the base plate.

Read more less