Electrical

8 AWG Heat Shrink Ring Terminal - 3/8" Stud Size - 25 PackRing terminals are a trusted way to create an electrical connection. By using ring terminals, users don't need to worry about the connector coming off. The ring fits over a stud or screw and doesn't pull loose as other terminals may. Pink ring terminals are for 8 AWG wires. They are easy to use and offer long-term protection. Heat shrink ring terminals protect against the elements in the most challenging of environments. This makes them the best moisture protection available. Heat shrink ring terminals possess a heat-activated adhesive liner. This liner is built to provide a durable, rugged, environmentally sealed connection for 8 AWG wires. Selecting the correct ring terminal isn't always an easy task. Contact a Pacer expert with any questions that you may have.Features: Protects terminations from water, condensation, salt spray, and corrosion Added vibration protection in rugged environments Provides strain relief Translucent, adhesive-lined polyolefin tubing is a durable insulator that provides a seal that keeps out moisture and contaminants and prevents wire corrosion Conforms to automotive manufacturers’ specifications for wiring repairs Color-coded tubing with wire gauge imprint provides easy identification of the correct part for the job Compliances: UL CSA RoHS Characteristics: Shrink Ratio: Approx. 3:1 at 135 °C Operating Temp: -55 °C - 125 °C Vol. Resistivity: 1015 Ohm-cm3 Dielectric Strength: 900-V/mil Voltage Rating: 600-V Specifications: Stud Size: 3/8” Terminal Pad Width: 0.59” Package Size: 25 Specifications: Gauge: 8 AWG Heat Shrink: Yes Package Qty: 25 Post Size: 3/8" Type: Heat Shrink Box Dimensions: 1"H x 2"W x 3"L WT: 0.2 lbs UPC: 840248210140 Brochure (pdf)

Read more less

22-18 AWG Heat Shrink Ring Terminal - 5/16" Stud Size - 25 PackRing terminals are a trusted way to create an electrical connection. By using ring terminals, users don't need to worry about the connector coming off. The ring fits over a stud or screw and doesn't pull loose as other terminals may. Pink ring terminals are for 8 AWG wires. They are easy to use and offer long-term protection. Heat shrink ring terminals protect against the elements in the most challenging of environments. This makes them the best moisture protection available. Heat shrink ring terminals possess a heat-activated adhesive liner. This liner is built to provide a durable, rugged, environmentally sealed connection for 8 AWG wires. Selecting the correct ring terminal isn't always an easy task. Contact a Pacer expert with any questions that you may have.Features: Protects terminations from water, condensation, salt spray, and corrosion Added vibration protection in rugged environments Provides strain relief Translucent, adhesive-lined polyolefin tubing is a durable insulator that provides a seal that keeps out moisture and contaminants and prevents wire corrosion Conforms to automotive manufacturers’ specifications for wiring repairs Color-coded tubing with wire gauge imprint provides easy identification of the correct part for the job Compliances: UL CSA RoHS Characteristics: Shrink Ratio: Approx. 3:1 at 135 °C Operating Temp: -55 °C - 125 °C Vol. Resistivity: 1015 Ohm-cm3 Dielectric Strength: 900-V/mil Voltage Rating: 600-V Specifications: Wire: 22-18 AWG Stud Size: 5/16” Terminal Pad Width: 0.47” Package Size: 25 Specifications: Gauge: 22-18 AWG Heat Shrink: Yes Package Qty: 25 Post Size: 5/16" Type: Heat Shrink Box Dimensions: 2"H x 3"W x 4"L WT: 0.2 lbs UPC: 840248206464 Brochure (pdf)

Read more less

30 Amp PowerCord PLUS Cord SetPart #: 199119The PowerCord PLUS has features you won't find on other cordsets.Features: LED Power Indicator Light 30 Amp 125V 50' Contour Grip Ends Thumbprint Locator Super Flexible 10/3 Cable Easy Lock System Includes: Marinco Easy Lock System Ring - A simple 1/8 twist provides a fast, positive watertight connection Threaded ring and Easy Lock ring WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Type: Cordset Length: 50' Amperage: 30a Box Dimensions: 5"H x 12"W x 12"L WT: 14.1 lbs UPC: 093344311772 Quick Guide (pdf)

Read more less

Pro Installer Link Joiner 6-WayThis tin-plated bus bar can be used to link 6 adjacent DC products together.  The rating varies from 350-650 Amps depending on how this busbar is wired, see drawing for details.  Made from tin-plated high-purity copper, this bar is intended for use with the BEP Pro Installer system but it has universal applications anywhere a high amperage link bus is needed. Pro Installer link bars provide the fastest and most economical way of connecting the Pro Installer line of products to save space and allow for the most compact installations. The common interconnection height of Pro Installer components allows link bars to quickly and easily convert a group of different products into a functional cluster. Links can be doubled to accommodate higher loads.Features: Tin-plated high-purity copper for maximum conductivity and corrosion resistance 650 AMP continuous rating between two adjacent positions 350 AMP continuous rating across all positions Bars can be doubled up for additional amperage This link bar is intended to be used with 3/8" studs Hole spacing is 2"  Overall dimensions 10.8" x 1" WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Pro Installer Link Joiner 5-WayThis tin-plated bus bar can be used to link 5 adjacent DC products together.  The rating varies from 400-650 Amps depending on how this busbar is wired, see drawing for details.  Made from tin-plated high-purity copper, this bar is intended for use with the BEP Pro Installer system but it has universal applications anywhere a high amperage link bus is needed. Pro Installer link bars provide the fastest and most economical way of connecting the Pro Installer line of products to save space and allow for the most compact installations. The common interconnection height of Pro Installer components allows link bars to quickly and easily convert a group of different products into a functional cluster. Links can be doubled to accommodate higher loads.Features: Tin-plated high-purity copper for maximum conductivity and corrosion resistance 650 AMP continuous rating between two adjacent positions 400 AMP continuous rating across all positions Bars can be doubled up for additional amperage This link bar is intended to be used with 3/8" studs Hole spacing is 2"  Overall dimensions 8.8" x 1" WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

4125 AC A-Series Circuit Breaker Lockout Slide Features: Allows only 1 double pole AC circuit breaker to be activated at a time Guarantees that AC power from 2 sources (shore power and genset or inverter) will not be mixed Fits all World or A-Series and Rocker double pole circuit breakers Uses circuit breaker mounting screw holes. Requires no special panel modification Includes mounting screws WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

5128ANL Fuse175A Ignition protected (conforming to SAE J1171)- safe for installation aboard gasoline powered boats Silver-plated connector blades for corrosion resistance Visible indication of blown condition 6,000 Ampere Interrupt Capacity (AIC) satisfies ABYC requirements for main DC circuit protection on large battery banks For use with Blue Sea Systems' ANL Fuse Blocks WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Amperage: 175a Fuse Type: ANL Type: Fuses Box Dimensions: 1"H x 3"W x 5"L WT: 0.05 lbs UPC: 632085051280

Read more less

100A Engine Starting Intermittent Duty SolenoidIntermittent switching of high amperage loads with a low amperage on-off switch.Features: Rated at 750A make/100A break, this solenoid is for intermittent use only: 10 seconds ON, 20 minutes OFF (ideal for engine cranking) Signal voltage of 12V DC and contact voltage of 6-12V DC #10/32 thread signal terminals Copper 5/16”-24 thread contact terminals Bracket mounting holes 5/16” x 19/32”, 2-13/64” on center Same as Cole Hersee part number M-200 WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

PT-7 Battery ChargerNewmar’s Phase Three Series Battery Chargers employ “Smart” battery charging technology for 12-volt systems aboard marine applications including workboats, military vessels, commercial vessels, and recreational craft. This charger interacts with batteries, providing the optimum three-stage charge process for fast recovery and conditioning, maximizing performance, and extending battery life.A selector switch adjusts output voltage to adapt to gel-cell, flooded lead-acid, or AGM battery types. An optional temperature compensation sensor also adjusts output for ideal voltage based on changes in the batteries’ ambient temperature. This model is housed in a rugged stainless-steel case with a durable white powder coat finish, and the internal circuitry is polyurethane-coated for maximum corrosion resistance.Features: “Smart” circuitry provides three-stage charging – bulk, absorption, float Gel-Cell/Flooded Lead-acid/AGM battery type switch selects optimum charge/float voltages Multiple isolated output banks; ammeter indicates total output current. (Except PT-7) The optional sensor adjusts output voltage based on battery temperature. (Except PT-7) Current limiting prevents damage from overloading Clean well-regulated output can be used as a power supply; can power loads directly without a battery in line Built to last – rugged stainless-steel case with a durable white powder coat finish with an optional drip shield and marinized internal circuitry Protection: Current Limiting, Thermal Protection, Forced Air Cooling, Drip Shield ABS-type approval for battery charging and power supplies Specifications: Input VAC (50-60 Hz.): 88-132 or 176-264  Input Amps @ Full Load: @ 115 VAC 2, @ 230 VAC 1     P.F. Rating: >.65  Max Output Amps: 7 Output Banks: 2  Battery Capacity (Amp-Hours): 14-70 Operating Temp. Rating Reference: T-1 Case Size Reference: A-1 Case Size (H x W x D): 10.5 x 5.0 x 2.8 inches (26.7 x 12.7 x 7.1 centimeters) Weight Lbs./Kg: 3.2/1.5 Optional Temp. Sensor Model: N/A Remote Panel Model: N/A  Equalize Option: No Output Indicator Reference: M-1 Compliance Reference: CG, CE     Temperature Rating References: Temperature: -10 degrees C to +45 degrees C     Derate Linearly From 100% @ 0 degrees C to 80% @ -10 degrees C Nominal Output Voltages at Gel/Flooded Switch Settings (without Temperature Compensation): Gel-Cell: 14.0 VDC Charge @ 50% load and 13.6 VDC Float @ .5 amp load Flooded/AGM: 14.2 VDC Charge @ 50% load and 13.4 VDC Float @ .5 amp load Compliance References: CG: USCG CFR 183.410 (Ignition protected) CE: Carries the CE mark ABS: PT Series meet SVR 2009 4-8-3/5.9, Under 90 meters Rules 2006 4-6-4/7.19, and HSNC 2007 4-8-3/5.13 This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Specifications: Charger Input - Voltage: 115/230v Charger Output - Amps: 7a Charger Output Voltage: 12v Charging Banks: 2 Inverter Input Voltage: 115/230v Inverter Output Voltage: 12v Outlet Qty: Hardwire Portable: No Box Dimensions: 6"H x 8"W x 12"L WT: 3.85 lbs Quick Guide (pdf)Owner's Manual (pdf)

Read more less

Sportsman Series Battery Charger - 40A - 4-10A-Banks - 12V-48VOur customers asked for a series of chargers that were smaller, lighter and economically affordable. The Sportsman Series of chargers answers these needs. This line of chargers is designed for all types of battery applications. Sportsman chargers have all the safety and reliability features that have made PRO Charging Systems chargers the #1 choice of most boat manufacturers, dealers and over 750,000 customers across the country. Advanced microprocessors and LED readings make the units even easier to use.Battery Charging System Designed for Use On Land and in Fresh and Salt Water The “Green” Charger: Totally “Repairable” Not a Throw-Away Unmatched Performance, Reliability, Safety and Quality TROUBLE FREE – Just Plug It In and Forget It! Join Over 750,000 of Our Satisfied Customers! Fully Automatic and Totally Waterproof Features: Approved for Wet Cell and AGM batteries Models also available for Gelled Electrolyte batteries Designed for use in fresh and saltwater DeltaVolt® Intuitive Charging Technology Waterproof, dependable, rugged construction Independent outputs Fully automatic / multi stage charging Zero spark technology Battery maintenance mode On-board diagnostic codes Temperature compensated Advanced microprocessor controlled Battery systems available: 12V – 48V LED lights indicate the state of charge Reverse polarity protected No installation restrictions FCC Parts A & B interference compliant DC charge cables = 5' AC power cord = 3' Approved and meets ISO 8846 Marine standards Ignition protected (US Coast Guard 33 CFR 183.410 May be used in many types of sporting applications including: Inland Watercraft Salt Water Watercraft Motorcycles Golf Carts Utility Vehicles… This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Specifications: Charger Output Voltage: 12/24/36/48v Charger Output - Amps: 40a Charging Banks: 4 Portable: No Charger Input - Voltage: 120v Box Dimensions: 10"H x 11"W x 14"L WT: 23.4 lbs UPC: 738562000304 Brochure (pdf)

Read more less

400A Class T Fuse Block Accessory KitSpecifications: Amps: 400 Amps Fuse: 400 Amps Weight: 1 (lbs) Weight: 0.45 (kg) Dimensions: 7 x 2 x 2.25 (in) Dimensions: 17.8 x 5.1 x 5.7 (cm) Applications:Inverter AccessoriesWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Fuse Type: Class T Type: Fuse Blocks Box Dimensions: 2"H x 4"W x 8"L WT: 0.95 lbs UPC: 622988079801 Owner's Manual (pdf)Brochure (pdf)

Read more less

SmartSolar MPPT 150/100-MC4 VE-CanThe MPPT VE.Can SmartSolar charger uses the latest and fastest technology to convert energy from a solar array into energy that optimally charges battery banks.The SmartSolar charge controller will even recharge a severely depleted battery. It can operate with a battery voltage as low as 0 Volts, provided the cells are not permanently sulfated or otherwise damaged.Models: 12/24/36/48 VoltFeatures: Ultra-fast Maximum Power Point Tracking (MPPT) Advanced Maximum Power Point Detection in case of partial shading conditions  Outstanding conversion efficiency Flexible charge algorithm Extensive electronic protection  Bluetooth Smart built-in  Internal temperature sensor and optional external battery voltage and temperature sensing via Bluetooth Fully discharged battery recovery function  VE.Can: the multiple controller solution VE.Direct or VE.Can Remote on-off Programmable relay Optional: SmartSolar pluggable LCD Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)Brochure (pdf)

Read more less