Electrical

Orion IP67 24/12-10A (120W)Completely encapsulated: waterproof, shockproof, and ignition protected. Water, oil, or dirt will not damage the Orion IP67 DC-DC Converter. The casing is made of cast aluminum and the electronics are molded in resin. Owner's Manual (pdf)

Read more less

Orion-Tr 24/12-5 (60W) DC-DCFeatures: High efficiency - Using synchronous rectification, full load efficiency exceeds 95% IP43 protection - When installed with the screw terminals oriented downwards Screw terminals - No special tools are needed for the installation Please contact your dealer for any returns, repairs or support issues related to this product. Owner's Manual (pdf)

Read more less

Phoenix Inverter 12/375 - 120V - VE.Direct GFCI Duplex Outlet - 300WInverters allow users to power domestic equipment - requiring 230V/120V AC - using 'leisure' or 'automotive' batteries rated at 12V, 24V or 48V DC. *This inverter has a GFCI Duplex Outlet.E.Direct Communication PortThe VE.Direct port can be connected to: A computer (VE.Direct to USB interface cable needed) Apple and Android smartphones, tablets, MacBook, and other devices (VE.Direct Bluetooth Smart dongle needed) Fully Configurable: Low battery voltage alarm trip and reset levels Low battery voltage cut-off and restart levels Dynamic cut-off: load-dependent cut-off level Output voltage 210 - 245V Frequency 50 Hz or 60 Hz ECO mode on/off and ECO mode sense level Monitoring:In- and output voltage, % load, and alarmsProven ReliabilityThe full bridge plus toroidal transformer topology has proven its reliability over many years.The inverters are short-circuit proof and protected against overheating, whether due to overload or high ambient temperature.High Start-Up PowerNeeded to start loads such as power converters for LED lamps, halogen lamps, or electric tools.ECO ModeWhen in ECO mode, the inverter will switch to standby when the load decreases below a preset value (min load: 15W). Once on standby, the inverter will switch on for a short period (adjustable, default: every 2,5 seconds). If the load exceeds a preset level, the inverter will remain on.Remote On/OffA remote on/off switch can be connected to a two-pole connector, or between battery plus and the left-hand contact of the two-pole connector.LED DiagnosisPlease see the manual for a description.To Transfer the Load to Another AC Source: The Automatic Transfer SwitchFor Victron’s low-power inverters, they recommend the Filax Automatic Transfer Switch. The Filax features a very short switchover time (less than 20 milliseconds) so that computers and other electronic equipment will continue to operate without disruption. Inverter Specifications: Cont. Power at 25 degrees C: (1) 375VA  Cont. Power at 25 degrees C / 40 degrees C: 300 / 260W Peak Power: 700W  Output AC Voltage / Frequency (adjustable): 230VAC or 120VAC +/- 3% 50Hz or 60Hz +/- 0,1% Input Voltage Range: 9,2 - 17 / 18,4 - 34,0 / 36,8 - 62,0V DC Low Shut Down (adjustable): 9,3 / 18,6 / 37,2V Dynamic (load dependent) DC Low Shut Down (fully configurable): Dynamic cut-off, see https://www.victronenergy.com/live/ve.direct:phoenix-inverters-dynamic-cutoff DC Low Restart & Alarm (adjustable): 10,9 / 21,8 / 43,6V Battery Charged Detect (adjustable): 14,0 / 28,0 / 56,0V Max. Efficiency: 89 / 89 / 90% Zero-Load Power: 5,6 / 6,1 / 8,5W Default Zero-Load Power in ECO Mode (default retry interval: 0,9 / 1,4 / 2,6W ECO Mode Stop & Start Power Setting: Adjustable Protection (2): a - f Operating Temperature Range -40 to +65 degrees C (fan-assisted cooling) Enclosure Specifications: Material & Color: Steel chassis and plastic cover (blue Ral 5012) Battery-Connection: Screw terminals Maximum Cable Cross-Section: 10mm² / AWG8  Standard AC Outlets: 230V: Schuko (CEE 7/4), IEC-320 (male plug included); UK (BS 1363), AU/NZ (AS/NZS 3112); 120V: Nema 5-15R, GFCI Protection Category: IP 21 Weight: 3,0kg / 6,6lbs Dimensions (H x W x D, mm); (H x W x D, inch): 86 x 165 x 260; 3.4 x 6.5 x 10.2 Accessories: Remote On-off: Yes Automatic Transfer Switch: Filax Standards: Safety: EN-IEC 60335-1 / EN-IEC 62109-1 / UL 458 (3) EMC: EN 55014-1 / EN 55014-2 / IEC 61000-6-1 / IEC 61000-6-2 / IEC 61000-6-3 Automotive Directive ECE R10-4: 1) Nonlinear load, crest factor 3:1; 2) Protection key: a) output short circuit b) overload c) battery voltage too high d) battery voltage too low e) temperature too high f) DC ripple too high Please contact your dealer for any returns, repairs or support issues related to this product. Specifications: GFCI: Yes Box Dimensions: 7"H x 10"W x 13"L WT: 9.1 lbs UPC: 8719076050209 Quick Guide (pdf)Owner's Manual (pdf)Brochure (pdf)

Read more less

Alternator 100 AMP 12V 1-2" Single Foot Spindle Mount K6 Pulley with Isolated GroundAlternator, 621 Series, 100A, 12V, Spindle Mount (Single Foot), 1-2in, K6 Serpentine Pulley, Isolated Ground 1" Motorola-Style Mounting;  Typical for Westerbeke, Lehman, Hino & Pathfinder Engines 2" Delco-Style Mounting;  Typical for Volvo Penta (Gas & Diesel), John Deere, Perkins, Mercruiser, Pleasurecraft, Crusader, Indmar, Marine Power & other GM-based EnginesReplaces: 621-100-SR-IGThis product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Brochure (pdf)

Read more less

Battery Switch 275A 12-48VDC Surface or Panel MountThe Battery Switch ON/OFF 275A is suitable for battery systems up to 48V. It has a unique ergonomic and aesthetic knob design. The knob is removable for isolation or safety purposes.The Battery Switch can be either surface or panel mounted, providing flexibility during install.The Battery Switch meets the ISO8846 Ignition Protection standard and is suitable for use in an engine room.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)Brochure (pdf)

Read more less

SmartSolar MPPT 150/100-TR VE.CanThe MPPT VE.Can SmartSolar charger uses the latest and fastest technology to convert energy from a solar array into energy that optimally charges battery banks.The SmartSolar charge controller will even recharge a severely depleted battery. It can operate with a battery voltage as low as 0 Volts, provided the cells are not permanently sulfated or otherwise damaged.MPPT: Ultra Fast Maximum Power Point TrackingThe MPPT VE.Can SmartSolar charger connects to a PV array of 150 or 250 Volt Voc and will automatically detect and charge your 12, 24, or 48V battery bank with current ranging from 70 to 100A depending on the model.The charge settings are fully programmable and can even be set up for different battery chemistries, like lead-acid, lithium, and others.Control Your Charger RemotelyThe MPPT VE.Can SmartSolar charger can be remotely controlled and configured over Bluetooth via the VictronConnect App. This allows device set-up, management, and at-a-glance information, such as battery voltage and current, PV voltage and current, and historical data.Daisy Chain Additional UnitsThe VE.Can SmartSolar charger is equipped with CAN bus ports. This allows for communication with additional VE.Can SmartSolar chargers. The additional units are simply "daisy-chained" to each other with a single RJ45 cable between the individual units.When connected to each other, all individual VE.Can SmartSolar chargers, will synchronize their charge stages. They can also send their data, via a single cable, to a GX monitoring device.Remote Monitoring and ControlIf the GX device is connected to the internet, the Victron Remote Management Portal (VRM) provides access to the full power of your solar charger(s).SmartSolar Control DisplayThe VE.Can SmartSolar charger is also equipped with a VE.Direct port like our other MPPT solar chargers. This port can be for single-unit monitoring or for streetlight control. The remote on/off connector can be externally controlled by a third-party device like a lithium battery. An optional plug-in LCD display/control provides live data, setup, and management, straight from the face of the device.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)Owner's Manual (pdf)Brochure (pdf)

Read more less

VE. Direct - 10M Cable (1 Side Right Angle Connector)Features: Cable Length: 10M 1 Side Right Angle Connector Warranty InfoWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.Please contact your dealer for any returns, repairs or support issues related to this product. Quick Guide (pdf)

Read more less

Heat Shrink Connector Kit *200-PieceFeatures: Heat-Activated Adhesive Sealant Use Heat Gun or Torch to Create a Corrosion-Proof Water-Tight Seal Heat-Shrink Tubing has a 3:1 Shrink Ratio What's Included? (27) Pink - Butt Connectors For 22-18 Gauge (AWG) wire (10) Pink - #10 Ring Connectors For 22-18 Gauge (AWG) wire (10) Pink - 1/4" Ring Connectors For 22-18 Gauge (AWG) wire (10) Pink - 5/16" Ring Connectors For 22-18 Gauge (AWG) wire (10) Pink - 3/8" Ring Connectors For 22-18 Gauge (AWG) wire (22) Blue - Butt Connectors For 16-14 Gauge (AWG) wire (10) Blue - #10 Ring Connectors For 16-14 Gauge (AWG) wire (10) Blue - 1/4” Ring Connectors For 16-14 Gauge (AWG) wire (10) Blue - 5/16” Ring Connectors For 16-14 Gauge (AWG) wire (10) Blue - 3/8” Ring Connectors For 16-14 Gauge (AWG) wire (15) Blue - Female Spade Connectors For 16-14 Gauge (AWG) wire (14) Yellow - Butt Connectors For 12-10 Gauge (AWG) wire (6) Yellow - #10 Ring Connectors For 12-10 Gauge (AWG) wire (6) Yellow - 1/4” Ring Connectors Fits 12-10 Gauge (AWG) wire (6) Yellow - 5/16” Ring Connectors For 12-10 Gauge (AWG) wire (6) Yellow - 3/8” Ring Connectors For 12-10 Gauge (AWG) wire (6) Red & (6) Black - 3" x 3/16" Heat-Shrink Tubing (3) Red & (3) Black - 3" x 3/8" Heat-Shrink Tubing

Read more less

Flat Ribbon Bonded RGB Cable 16/4 AWG  - Red, Light Blue, Green & White - 100'Features: Tinned Bonded Copper Conductor Colors: Red, Light Blue, Green and White Spool Length: 100' 16/4 AWG WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Length (Feet): 100' Gauge: 16/4 AwG Color: Red/Blue/Green/White Box Dimensions: 5"H x 7"W x 7"L WT: 4.8 lbs UPC: 091887991321

Read more less

Safety Duplex Cable - 14/2 AWG - Red/Yellow - Flat - 1,000'Ancor safety duplex cable features red and yellow Marine Grade primary conductors (correctly color-coded to ABYC standards) in a white common jacket that is made for easy removal while providing the best abrasion resistance available. These cables exceed UL 1426 standards and are made from the highest quality ultra flexible (Type 3/Class K) tinned copper stranding that provides maximum protection against corrosion and electrolysis while resisting fatigue due to vibration and flexing. The premium vinyl insulation is rated at 600V, 105°C dry and 75°C wet, stays flexible even in extreme cold (-40°F/C) and resists salt water,battery acid, oil, gasoline, heat, abrasion and ultra-violet radiation.WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Color: Red/Yellow Length (Feet): 1,000' Gauge: 14/2 AWG Box Dimensions: 13"H x 13"W x 19"L WT: 57.5 lbs UPC: 091887805994

Read more less

Black 2/0 AWG Battery Cable - Sold By The FootFeatures: ANCOR Marine Grade™ wire is manufactured from tinned copper stranding for maximum protection against corrosion and electrolysis. Ultra flexible (Type 3) stranding resists fatigue due to vibration and flexing. ANCORs proprietary premium vinyl insulation stays flexible even in extreme cold and resists salt water, battery acid, oil, gasoline and ultra-violet radiation. Exclusive insulation is rated at 600V, 105°C dry and 75°C wet, and is resistant to heat and abrasion. Exceeds all UL 1426, US Coast Guard Charter boat (CFR Title 46) and ABYC standards WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Color: Black Length (Feet): Sold By The Foot Gauge: 2/0 AWG Box Dimensions: 1"H x 1"W x 12"L WT: 0.6 lbs Owner's Manual (pdf)

Read more less

On-Board Precision Charger MK-440 PCL 4 Bank x 10 AMP LI Optimized ChargerLonger run times. Shorter charge times. That's the precision difference that keeps anglers on the water longer and puts more fish in the boat. Now, the next generation of this legendary line of chargers has been optimized for 12-volt lithium (LiFePO4) batteries. Precision chargers feature battery-type selection by the bank, which now includes charge curves specially formulated for the high demands of lithium batteries, and can even wake these battery types from standby.Features: Battery Type Selection: Each charging bank can be selected to your specific battery type (Lithium (LiFePO4) AGM or flooded lead acid) to guarantee a safe, protected charge Automatic Temperature Compensation: Precision chargers sense and adjust to ambient temperature fluctuations to ensure a fast, accurate charge Low-Line Voltage Compensation: When outlets don't put out the 120 volts they are supposed to, Precision Chargers compensate to deliver a fast, consistent charge no matter what Battery Equalization: Cleans and protects your battery (flooded lead-acid only) every time you plugin. Also activates a more rigorous, complete cleaning at the push of a button Digital Control: Microprocessor-based design delivers a faster, more precise charge every time. Precision chargers can even wake dead 12-volt lithium (LiFePO4) batteries from standby automatically. LED Indicator Lights: Inform of charge stage, maintenance mode status, error notifications, and full charge Automatic Multi-Stage Charging: Controls the voltage and current your battery gets throughout the charging cycle, ensuring a fast, safe and precise charge Waterproof Construction: All on-board chargers are built to be waterproof, shock-resistant and vibration-resistant 3-Year Warranty: All battery chargers come with a full 3-year replacement warranty Specifications: Product Dimensions: 9.88 in x 9.88 in x 3.5 in Product Weight: 10.5 lb Charger Style: On-Board Output per Bank: 10 amps Wattage: 600W Charge Time: 4-6 hours Power Source: On-Shore AC Battery Type: 12v Lithium LiFePO4, 12v AGM, 12v Flooded Lead Acid 12v Lithium-Ion (LiFePO4) Optimized: Yes Waterproof: Yes Digital Control: Yes Automatic Temperature Compensation: Yes Battery Equalization: Yes Battery Type Selection: Yes LED Display: Yes Saltwater Compatible: Yes Battery Connection: Ring Terminal Warranty: Three-Year Warranty Specifications: Charger Input - Voltage: 120v Charger Output - Amps: 10a Charger Output Voltage: 12/24/36/48v Charging Banks: 4 Portable: No Box Dimensions: 5"H x 14"W x 18"L WT: 13.4 lbs UPC: 029402050000

Read more less