Marine Hardware

PSS Shaft Seal 2-1/2" Shaft 4" TubeShaft Diameter: 2-1/2"Stern Tube Diameter (D): 4"Total Length (A): 9.625"Total Length (compressed) (Compressed A): 8.375"Rotor Diameter (B): 4.2"Carbon Cuff Diameter (C): 3.75"Stern Cuff Length (E): 2"The PSS Shaft Seal is the number one selling marine mechanical seal worldwide and is installed as standard equipment by many of the worlds most reputable boat builders / yards. The PSS Shaft Seal is also recognized as the premiere retrofit (aftermarket) seal on the world market. Certified by Bureau Veritas, ABS & Rina: Boat builders / yards recognize the advantages and value of installing the PSS as it eliminates the maintenance, constant adjustment & cost associated with traditional packing type glands. Aside from these benefits, the PSS Shaft Seal helps to eliminate water in the bilge (100% water tight) & wear to the propeller shaft. The PSS Shaft Seal can be easily retrofitted and is available for shafts ranging from 3/4" (20mm) to 6" (150mm).The PSS Shaft Seal is a mechanical face seal that is created between the flat surfaces of the rotating stainless steel rotor and the stationary carbon flange. The stationary carbon flange is attached to the vessels stern tube with hose clamps and the carbon flange is attached to the front side of the bellows with hose clamps. The stainless steel rotor is fit on the shaft in front of the carbon flange. The stainless steel rotor is used to compress the bellows before the collar is secured to the shaft with set-screws. This compression (pre-load) maintains contact between the faces and allows the PSS to compensate for the thrust from the propeller. The carbon flange is bored larger than the shaft diameter allowing it to "float" around the shaft and thus compensate for most misalignment and vibration problems. The stainless steel collar is sealed to the shaft by two o-rings that are recessed into the bore of the collar. These o-rings rotate with the shaft and stainless steel rotor and do not experience wear during operation.**As with any rubber hose below waterline, the PSS bellows must be inspected on a regular basis for any sign of wear, aging or chemical deterioration. PYI suggests as preventative maintenance that the PSS bellow be replaced in six year intervals. During bellows replacement it is recommended the o-rings & set screws in the stainless steel rotor also be replaced."Bellows may need to be more frequently inspected in an environment where non-sealed batteries emit sulfuric acid. Sulfuric acid vapor will accelerate rubber deterioration, as will an ozonater.The Maintenance Kit includes the items you need to properly maintain your PSS Shaft Seal. Included in the kit is one (1) PSS bellow, two (2) O-rings, five (5) set screws, four (4) new hose clamps and an allen key. Brochure (pdf)

Read more less

Grabber Catch Latch - Side Mount - Black - Pull-Up Force 22N (5lbf)Features: Spring-loaded over-center latching One assembly includes catch and keeper Material and Finish: PC/ABS, black Performance Details: Operating temperature range: -30ºC (-20ºF) to 60ºC (140ºF) Flammability rating: UL94-HB Installation Notes: Orient keeper to latch. The arrow on the keeper should point towards the cam. Mount to door and adjust for smooth latching. Minimum distance from frame (or surface on which catch subassembly is mounted) to centerline of door hinge is 150 (5.9)

Read more less

90° P-Trap Fuel Tank Vent - Flush Mount - Black with Stainless Steel Vent HeadThis Attwood 90-Degree P-Trap Fuel Tank Vent reliably helps prevent water from entering the fuel tank while still allowing air to vent freely during normal sea conditions and washdowns. This vent’s effectiveness. eliminates the need for an anti-siphon loop in the vent hose. This is a flush mount vent for use with a 5/8-inch interior diameter hose. It requires a 1-3/8-inch installation hole and can be used with a maximum hull thickness of 1 inch.Features: This black vent with a stainless steel vent head meets ABYC standards Flush Mount - 5/8" I.D. hose (inch) 1-3/8" install. hole size (inch) 1" Max. hull thickness *Compatible with Ethanol blended fuels Quick Guide (pdf)

Read more less

Cowl VentilatorAttwood hull-mounted vents are designed to install by fastening as a complete unit from either inside or outside the hull. Ventilation hose (not included) twists into the bottom of the box to form a raised water barrier. Plastic vents are corrosion-resistant, will not discolor. All collector boxes and vents are designed for intake or exhaust and meet ABYC H-2 cross sectional area requirements.For use with 3" I.D. wire-supported ventilation hose. Features flexible hose flange that is screwed onto hose, then vent snaps onto the flange. Vent constructed of chrome-plated die-cast Perma-Plate® ZAMAK. Flange is non-corrosive plastic. Installs with #8 screws.Installation Hole Size: 3-1/4" to 3-1/2"WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Quick Release Fender Lock Receiver OnlyStainless Steel & High Polish For dockside safety and convenience, Taco Marine's new fender lock ensures secure, quickly stored fender lines. The fender lock ensures that lines remain at the optimum length with the mounting pin attached. At the dock, you simply insert the pin into the fitting and your boat is protected, with the fenders their ideal position.The "Fender Lock Receiver Only" allows boaters the ability to quickly and easily place fenders in multiple places where they prefer to hang them off the boat at the desired height position every time.Features: Designed for simple single hand operation Will allow easy installation and removal of float style fenders Limited 3 year Warranty Specifications: Stainless Steel Type 316 Drain plug: 1/4" NPT This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Read more less

Latch-tite™ Lifting Handle - 2-1/2" Round - Stainless SteelStainless Steel Type 316Deluxe PolishedLatch-tite™ handles have been designed to provide high performance, trouble free use in the most hostile conditions. The latches and all shafts and tongues are made from cast type 316 stainless steel. Round design enhance any marine craft. Latches can be installed vertically or horizontally, making them ideal for any opening.The Latch-tite™series is for applications that require a heavy-duty, high performance construction and high quality appearance.Features: Cast stainless steel Deluxe polish finish Unique patented stainless steel shaft with bushing and twin Nitrile “O” rings for greater protection against water penetration Over center anti-rattle handles provide quiet operation Concealed fasteners Mold plugs available upon request for boat builders Specifications: Dimensions: 2-1/2" Diameter Edge Thickness: 5/32" Adjust Depth: 1-3/4" Hole Size: 2-1/16" Overall Depth: 2-5/8" Screw: #8 This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Read more less

Louvered Door & FrameCutout: 11" x 11"Left Hand Opening

Read more less

Description: 316 S.S. Heavy Duty Hollow Base Cleats Length - 8" (20cm) Height - 2-1/4" Fastener - 1/4" (4) Weight - 23.5 oz.Material: 316 Stainless Steel Specifications: Finish: Polished Size: 8" Construction: Stainless Steel Box Dimensions: 2"H x 2"W x 8"L WT: 1.15 lbs

Read more less

Table Support - Surface Mount - Fits 2-3/8" PedestalsAluminum - Brite AnodizedTable support options allow for fixed table tops receiving a dual tapered top column. The 60mm system is ideal for smaller diameter table tops in particularly tight quarters.Features and Benefits Bases are tapered for secure fit Designed for fixed table tops and dual taper columns Base Outside Diameter: 7" This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Read more less

SuproFlex Rub Rail Kit - Black with Flex Chrome Insert - 1.6"H x .78"W x 60'LThe SuproFlex Rub Rail Kit is lightweight and ultra-flexible to save you time and money while providing a seamless precision fit. The innovative SuproFlex series is co-extruded vinyl that provides two levels of hardness – ensuring enhanced protection from impact. SuproFlex Rub Rail requires minimal heating – reducing installation time and manpower. Additionally, SuproFlex Rub Rail requires no pre-forming and easily molds to most hull shapes. Features: Ideal for boats up to 65' Co-extruded to provide two levels of hardness Rigid backing and soft durometer front Shock-absorbing channels for higher impact resistance Lighter weight than traditional vinyl rub rail Requires no pre-forming and minimal heating Pairs with V12-0307CP (included in kit) Made in the USA 5-year limited warranty This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Read more less

Teak Marine LumberThickness: 1/2"Width: 1-3/4"Length: 36"

Read more less

TR8 with D-Shackle Safety Pin - 3/4" ShackleFeatures: Perpendicular or parallel release directions Hitch pin lock for device locking safety Computer generated parts precision-cut from aerospace grade stainless steel plate Low friction, low effort lanyard-style release for maximum user safety On load/off load releasing All parts 100% stainless steel No springs Break Load - 35,210 pounds and SWL 7,042 pounds WARNING: This product can expose you to chemicals including Titanium dioxide which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov. Owner's Manual (pdf)Brochure (pdf)

Read more less