Marine Hardware

Screw-Out Deck PlateThe Beckson Screw-Out Plate was designed to provide access without the use of tools, with a single start non-jamming (no cross-thread), extra strong, self-cleaning buttress thread. They incorporate a self-aligning center and an innovative gasket to assure a watertight seal. A back-up sealing wall leaves the plate watertight, even if the gasket is removed. Our clear center plates permit observation of controls or gauges and visual inspection without the necessity of removing the center. Deck plates are used for access to shut-off valves or back-fastenings, inspection, and clean out for tanks and compartments. A screw-out plate should be used in compartments where a change in air pressure due to temperature or oil canning can occur. Center: Clear Color: Black

Read more less

Screw-Out Deck PlateThe Beckson Screw-Out Plate was designed to provide access without the use of tools, with a single start non-jamming (no cross-thread), extra strong, self-cleaning buttress thread. They incorporate a self-aligning center and an innovative gasket to assure a watertight seal. A back-up sealing wall leaves the plate watertight, even if the gasket is removed. Deck plates are used for access to shut-off valves or back-fastenings, inspection, and clean out for tanks and compartments. A screw-out plate should be used in compartments where a change in air pressure due to temperature or oil canning can occur. Center: Smooth Color: Black

Read more less

Outboard Motor Bracket - Stainless Steel - Max 10HPStainless Steel Outboard Motor Bracket Up to 10 horse power. The Adjustable outboard motor bracket is stainless steel construction and non-corrosive for saltwater use. Designed for use with power or sail boats. Manual operation means no power required to raise and lower your auxiliary outboard motor. Features Stainless Steel Construction Fits Motors up to 10 horse power at 110 pounds.14" travel.

Read more less

Twin Roller Door Catch - White Upgrade your cabinet or wardrobe with these Twin Roller Door Catches. Sturdy injection molded nylon construction these catches provide secure door closure. Installs with four #6 RH fasteners (not included). WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

PSS Shaft Seal 2-1/2" Shaft 4" TubeShaft Diameter: 2-1/2"Stern Tube Diameter (D): 4"Total Length (A): 9.625"Total Length (compressed) (Compressed A): 8.375"Rotor Diameter (B): 4.2"Carbon Cuff Diameter (C): 3.75"Stern Cuff Length (E): 2"The PSS Shaft Seal is the number one selling marine mechanical seal worldwide and is installed as standard equipment by many of the worlds most reputable boat builders / yards. The PSS Shaft Seal is also recognized as the premiere retrofit (aftermarket) seal on the world market. Certified by Bureau Veritas, ABS & Rina: Boat builders / yards recognize the advantages and value of installing the PSS as it eliminates the maintenance, constant adjustment & cost associated with traditional packing type glands. Aside from these benefits, the PSS Shaft Seal helps to eliminate water in the bilge (100% water tight) & wear to the propeller shaft. The PSS Shaft Seal can be easily retrofitted and is available for shafts ranging from 3/4" (20mm) to 6" (150mm).The PSS Shaft Seal is a mechanical face seal that is created between the flat surfaces of the rotating stainless steel rotor and the stationary carbon flange. The stationary carbon flange is attached to the vessels stern tube with hose clamps and the carbon flange is attached to the front side of the bellows with hose clamps. The stainless steel rotor is fit on the shaft in front of the carbon flange. The stainless steel rotor is used to compress the bellows before the collar is secured to the shaft with set-screws. This compression (pre-load) maintains contact between the faces and allows the PSS to compensate for the thrust from the propeller. The carbon flange is bored larger than the shaft diameter allowing it to "float" around the shaft and thus compensate for most misalignment and vibration problems. The stainless steel collar is sealed to the shaft by two o-rings that are recessed into the bore of the collar. These o-rings rotate with the shaft and stainless steel rotor and do not experience wear during operation.**As with any rubber hose below waterline, the PSS bellows must be inspected on a regular basis for any sign of wear, aging or chemical deterioration. PYI suggests as preventative maintenance that the PSS bellow be replaced in six year intervals. During bellows replacement it is recommended the o-rings & set screws in the stainless steel rotor also be replaced."Bellows may need to be more frequently inspected in an environment where non-sealed batteries emit sulfuric acid. Sulfuric acid vapor will accelerate rubber deterioration, as will an ozonater.The Maintenance Kit includes the items you need to properly maintain your PSS Shaft Seal. Included in the kit is one (1) PSS bellow, two (2) O-rings, five (5) set screws, four (4) new hose clamps and an allen key. Brochure (pdf)

Read more less

Stainless Steel Pedestal Guard Mounting Feet - PairEdson Pedestal Guard Mounting Feet are available in pairs as a direct replacement for Edson’s black plastic feet. Gasket and bushing allow for mounting 1”, 1-1/8” or 1-1/4” guard pipes. Nuts and washers included.

Read more less

Utility/Wardrobe HookFeatures: Chrome Plated Zinc Projection: 1-3/8" Base Width: 1-1/8"

Read more less

Surface Mount Drawer Pull - Chrome Plated ZincSpecs: Chrome Plated Zinc Alloy Overall Width: 3-7/16" Inside Width: 2-5/16" Screw Size: 6

Read more less

Pipe Deck Fill 1-1/2" GasFeatures: 316 S.S. 1-1/2" Pipe Gas Deck Fill with Key Chain included Flange: 3-3/8" Fastener: #10 (3) Weight: 20oz Replacement cap & chain is P/N 6074

Read more less

Description: Plate: 3/4" x 3" Material: 304 Stainless Steel Stock: 1/2" Eye Ring Diameter: 1-1/2"Thread Length: 3-7/16"

Read more less

Description: Plate: 3/4" x 2-1/4"Material: 304 Stainless Steel Stock: 3/8" Eye Ring Diameter: 1"Thread Length: 3-7/16"

Read more less

Clam Shell Midget Vent 1-1/2" x 1-3/4" Material: 304 Stainless Steel Size: 1-1/2" x 1-3/4" Fastener: #6 (3)

Read more less