Marine Navigation & Instruments - NMEA Cables & Sensors

Submersible Pressure Transducer 0-3 PSIMaretron’s submersible pressure transducers indicate tank levels and can be installed directly in the tank. Please follow these instructions to mount and connect a submersible pressure transducer to an NMEA 2000® network via a Maretron FPM100 Fluid Pressure Monitor. Maretron recommends one of two methods for mounting a submersible pressure transducer in a tank: 1) without a restraining tube, and 2) with a restraining tube.The submersible pressure transducers are designed for a tank with a 5-hole SAE J1810 fitting at the top. Install the mounting plate with cord grip onto the transducer cable, with the rounded hex section of the cord grip facing away from the transducer.Lower the pressure transducer into the tank such that the transducer lies at the lowest point of the tank and tighten the cord grip to secure the cable. On a tank with a flat bottom, the transducer may slide from side to side with the motion of the vessel but will not rotate due to the stiffness of the cable. It is also possible to mount the pressure transducer inside a restraining or focus tube (sold separately, Maretron part number TFT-5H).Pressure Transducer MountingConnect the two wires of the pressure transducer to a free pressure monitoring channel. Connect the red wire from the pressure transducer to the channel's positive (+) terminal and connect the black wire from the pressure transducer to the negative (-) terminal of the channel. The example in Figure 1 shows the pressure transducer connected to switch channel 0, with the white wire connected to "P0+" and the brown wire connected to "P0-." Submersible pressure transducers have a small plastic vent tube in the connecting cable.Use a Maretron DSM Series Display (firmware 1.4.7 or higher) or a PC running Maretron’s N2KAnalyzer software (version 1.4.19 or higher) to configure the connected channel(s) on the FPM100.Supply power to the NMEA 2000 network and verify that the pressure channel indicates a valid pressure reading.Specifications: Operating Range: 0 to 3 PSI (0.207 bar) Depth Range (Water): 83.1” (2.11 m) Depth Range Diesel (820 kg/m3): 101.3” (2.57 m) Depth Range Gasoline/Petrol (750 kg/m3): 110.8” (2.81 m) Cable Length: 17 ft (5.18 m) Sensor Type: Gauge (Vent Tube) Output: 4 – 20 mA current loop, loop powered Excitation Voltage: 8 VDC to 28 VDC Compatible Fluids / Gases: Diesel, Diesel Exhaust Fluid (DEF), Gasoline/Petrol, Hydraulic Fluid, Kerosene, Motor Oil, Fresh Water, Sea Water, Waste Water Operating Temperature: 14 degrees F to 158 degrees F (-10 degrees C to 80 degrees C) Storage Temperature: -4 degrees F to 176 degrees F (-20 degrees C to 80 degrees C) Accuracy: ±0.3% Full Scale typ. at 25°C Total Error Band (TEB): ±1.0% Full Scale typ. (-10 degrees C to 70 degrees C) Non-Linearity, Hysteresis (NLH): ±0.2% Full-Scale typ. Best Straight Line (BSL) at 25°C Temperature Compensation: 23 degrees F to 122 degrees F (0 degrees C to 50 degrees C) Accuracy: ±1% Full Scale Linearity: 0.5% Full Scale Repeatability: 0.05% Full Scale Full-Scale Thermal Error: 0.04% Full Scale/°F (0.07% Full Scale/degrees C) Long-Term Stability: 0.2% Full Scale/year Response Time: 150ms Proof Pressure: 2 × Full Scale Burst Pressure: 3 × Full Scale Reverse Voltage Protection: ± 30V for 3 minutes Construction: 316L stainless steel body and diaphragm, polyether polyurethane cable, chloroprene boot EMC Compatibility: 10 Volts/meter per EN 61000-4-3 Weight: 24.8oz (703g) Owner's Manual (pdf)

Read more less

Pressure Transducer 0 to 3 PSI - for the FPM100 Fluid Pressure MonitorWARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov. Owner's Manual (pdf)

Read more less

Like the straight Micro/Mid Field-attachable connectors, the 90 degree field attachable connectors allow you to make field conections to bulk cable. The 90 degree connectors are particularly well suited for tight spaces like the back of displays where there is limited space for a straight connector. Useful in tight spaces or where sharp corners need to be made Waterproof rated to IP67 Specifications: Connection Gender: Female Box Dimensions: 1"H x 1"W x 1"L WT: 0.1 lbs UPC: 873804001708

Read more less

Mini/Micro TeeA Tee is used to tap into the trunk line for adding a drop connection. A Mini/Micro Tee has Mini connectors for the trunk lines and a Micro connector for the drop line.Gold contacts for greatest reliability Keyed connectors for error-free connectionsMini Male (left)Micro Female (bottom)Micro Female (right)

Read more less

Our NMEA 2000 network updater provides the convenience of updating Garmin products and NMEA 2000 accessories that do not have an SD card slot. Simply download a software update to an SD card and insert the card into the network updater. Using a simple plug & play installation, the network updater easily and temporarily connects to your NMEA 2000 network.WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Data Interface: NMEA 2000 Box Dimensions: 3"H x 6"W x 6"L WT: 0.2 lbs UPC: 753759102180

Read more less

NMEA 2000® Backbone/Drop Cables (Right Angle) - 1'Extend your NMEA 2000 backbone with our 1 foot (0.3 m) or 6 foot (1.82 m) right angle backbone cable.WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Cable Length (Feet): 1' Data Interface: NMEA 2000 Box Dimensions: 1"H x 4"W x 6"L WT: 0.3 lbs UPC: 753759138264

Read more less

NMEA 2000 terminator - femaleWARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Connection Gender: Female Data Interface: NMEA 2000 Box Dimensions: 1"H x 1"W x 1"L WT: 0.02 lbs UPC: 753759078171

Read more less

NMEA 2000 Terminator - FemaleThis NMEA 2000 terminator allows for proper termination of an NMEA 2000 network. The couplers connect to the corresponding T-connectors for a simple installation. Features: Includes (1) female NMEA 2000 terminator Please note that installation of a NMEA 2000 network requires (1) male and (1) female terminator. 1-Year Limited Warranty

Read more less

AS GPS NMEA ONIX Splitter CableONIX Splitter Cable to connect with optional external GPS receiver AS GRP or AS GPS HS for 1 additional NMEA 0183 communicationWARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Data Interface: NMEA 0183 Box Dimensions: 2"H x 8"W x 9"L WT: 0.4 lbs UPC: 082324038938

Read more less

Micro Double-Ended Cordset - 0.5M - *Case of 6*Mechanical Contact Carrier Mat/Color: Thermoplastic PUR/Blue-Gray Molded Body Mat/Color: Thermoplastic PUR/Blue-Gray Contact Mat/Plating: Brass/Gold Coupling Nut Mat/Plating: Brass/Nickel Connector Outside Diameter: 0.59" Electrical Current Rating: 4.0 Amps Voltage Rating: 250 V Cable Outer Jacket Mat/Color: PVC/Gray Conductor Insulation Material: HDPE (data pair), SRPVC (power pair) Number of Conductors: 4X22 AWG, 22 AWG Drain Wire Shielding (3-Levels): FOIL (Overall), FOIL (Power Pair), FOIL (Data Pair) Environmental Protection Class: IEC IP68, NEMA 1,3,4,6P Temperature Rating: -40° C to 80° C to (-40° F to 176° F)Approvals (Cable) UL: PLTC 75° C Sunlight Resistant E90625, AWM 80° C 300V (Cable) CSA: CMX-OUTDOOR-CMG LL54185 75° C, AWM I/II A/B 80C 300V FT4 NMEA: NMEA 2000 Approved Specifications: Cable Length (Feet): 2' Box Dimensions: 1"H x 5"W x 5"L WT: 0.6 lbs

Read more less

NMEA 2000 Backbone Cable - 10MAncor's NMEA 2000 Approved Backbone Cables offer connection to an NMEA 2000 tee connector. The yellow couplers connect to the corresponding Ancor tees creating a simplified, color coded network installation. The backbone cables are available in four lengths from 0.5 meter (1.6 feet) to 10 meters (32.8 feet) to cover a wide variety of applications.Features: Color coded for easy installation and component identification Large 18 AWG power conductors to reduce voltage drop and provide better reliability for critical backbone cables NMEA 2000 Approved, 100 percent universal and compatible with other manufacturers' products WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications: Cable Length (Feet): 33' Data Interface: NMEA 2000 Box Dimensions: 3"H x 9"W x 10"L WT: 2.8 lbs UPC: 091887982251 Brochure (pdf)

Read more less

Protective Screw Cover for N2K Connectors *10-PackScrew-cap covers for the NMEA 2000 Micro connectors, female and male versions available. *Sold in quantities of 10.

Read more less