Boat Outfitting - Jack Plates

Single Paddle Trim SwitchFor complete control of engine trim and tilt, trim tabs, jackplates, and other onboard systems, the innovative Paddle Trim system is the answer.Adaptable to existing front-mount hydraulic and tilt helms, the Paddle Trim is ergonomically designed to allow the driver to make precise adjustments to the attitude of the boat or other systems without removing his hand from the steering wheel.Features: Equipped with one waterproof “MOM.ON-OFF-MOM.ON switch Max load 5 Amp @ 12VDC. Suitable for any kind of steering wheel dish. Max wheel dia. 400 mm (15.7”). Easy to install on the following steering systems: Front and tilt mount hydraulic helms Tilt mount mechanical helms The wiring harness, labels, and mounting hardware kit are included. The mounting plate differs between the front and tilt mount. Installation is ordered separately.

Read more less

PT-35 Tilt & Trim for Up to 35hpElevate your boating experience with the CMC PT-35 Tilt & Trim, designed for up to 35 hp motors. This lightweight, durable unit enhances stability and performance, ensuring better handling and lower fuel consumption.Features: Rated for 35 hp power and smaller motors 5 1/2" Setback to Enhance Boat Stability and Performance 1/4" 6061 T6 Extruded Aluminum Construction with Stainless Steel Fasteners Accommodates Clamp-on or Bolt-on Motors Without the Need for an Adapter Specifications: Power rating: up to 35 hp Set Back: 5 1/2" Trim and tilt: 84° Inside dimension of the motor mounting area: 11" Electric hydraulic actuator rating: 7853 lbs. of thrust Weight: 24 lbs Electric Hydraulic Tilt & TrimYou Get Power Tilt & Trim, Better Boat Handling, More Speed, Lower Fuel Consumption and No More Back Strain!Note: The inside dimension of the motor mounting area of the PT-35 is 11 inches. Before ordering, please make sure that the maximum width of the clamp mounting feet and/or mounting bolts of the motor that must fit into this area does not exceed this 11 inch limit. Refer to the transom view drawings. Mounting bolts are not included with the PT-35.

Read more less

Z-Lock™ 4" Set Back Manual Single Adjust Jack PlateZ-Lock Jack Plate Revolutionary Design Adds Strength and Stability. The excellence of T-H Marine's HI-JACKER™ jack plate series continues with the Z-Lock Manual Jack Plate design upgrade.Features: Z-Lock™ Jack Plate Design Eliminates Side Slippage Matching slotted extrusions LOCK side plates in place Strong Aircraft Grade Aluminum Full ½” Material For Strength Handles All V6 and V8 Outboards up to 300 hp Easy to Adjust From Top of Jack Available in 4", 6", 8", 10" and 12" setbacks 5" of Vertical Adjustment WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

6" Hole Shot Plate for Z-Lock™ Jack PlateREVOLUTIONARY...SIMPLE...UNIQUE...EXCITING.These are but a few of the comments coming from users of T-H Marine's HOT SHOT™ hole shot plates. This simple but revolutionary plate easily attaches to the bottom of our jack plate to provide an amazing 18 to 20 percent better hole shot. That's 2 to 3 seconds faster out of the hole. Hot Shot™ does this by dramatically reducing water drag on take-off as well as serving as a center trim tab. An added advantage is the ability to stay on a plane and virtually eliminate porpoising at lower speeds.Models available for Z-LOCK™ manual plates.  Features: Provides Improved Hole Shot Reduces Water Drag at Take Off Reduces Porpoising WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

ATLAS™ 10" Set Back Hydraulic Jack Plate - Heavy DutyT-H Marine’s ATLAS™ Hydraulic Jack Plate is now available in a “HEAVY DUTY” upgrade.T-H Marine’s ATLAS™ Hydraulic Jack Plate is the #1 selling jack plate in the world and the #1 Choice by fishing professionals and boat manufacturers. With the ATLAS™ HEAVY DUTY, the product is available for applications on even larger outboards, rated for engines up to 400 hp.5 REASONS YOU SHOULD CHOOSE THE ATLAS™ HYDRAULIC JACK PLATE ATLAS™ is truly the best hydraulic jack plate in the world ATLAS™ is factory installed by more boat manufacturers than any other plate ATLAS™ is used by more professional fisherman than any other hydraulic jack plate ATLAS™ is the #1 selling hydraulic plate in the world – sold & serviced by more outlets ATLAS™ hydraulic actuator is made in the U.S.A. vs. our competitors being from China 6 WAYS THE ATLAS™ CHANGED HYDRAULIC JACK PLATES FOREVER ATLAS™ is made by T-H Marine/CMC, who were the FIRST to offer an actuator inside the jack plate – the competition copied ATLAS™ was the first plate to offer predrilling for shallow water anchors – the competition copied ATLAS™ was the first and only plate that did not require regular grease lubrication – the competition design cannot do that ATLAS™ was the first plate to include a heavy duty safety cable to protect boaters from engine entering cockpit upon failure ATLAS™ was the first plate to offer a very simple actuator replacement in the field ATLAS™ was the first major development in hydraulic jack plates in over a decade – spurring hydraulic jack plate improvement WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

ATLAS™ 14" Set Back Hydraulic Jack Plate PolishedRated for engines up to 300hp or up to 625 pounds dry weight.5 REASONS YOU SHOULD CHOOSE THE ATLAS™ HYDRAULIC JACK PLATE ATLAS™ is truly the best hydraulic jack plate in the world ATLAS™ is factory installed by more boat manufacturers than any other plate ATLAS™ is used by more professional fisherman than any other hydraulic jack plate ATLAS™ is the #1 selling hydraulic plate in the world – sold & serviced by more outlets ATLAS™ hydraulic actuator is made in the U.S.A. vs. our competitors being from China 6 WAYS THE ATLAS™ CHANGED HYDRAULIC JACK PLATES FOREVER ATLAS™ is made by T-H Marine/CMC, who were the FIRST to offer an actuator inside the jack plate – the competition copied ATLAS™ was the first plate to offer predrilling for shallow water anchors – the competition copied ATLAS™ was the first and only plate that did not require regular grease lubrication – the competition design cannot do that ATLAS™ was the first plate to include a heavy duty safety cable to protect boaters from engine entering cockpit upon failure ATLAS™ was the first plate to offer a very simple actuator replacement in the field ATLAS™ was the first major development in hydraulic jack plates in over a decade – spurring hydraulic jack plate improvement WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

ATLAS™ 14" Set Back  Hydraulic Jack Plate - Heavy DutyT-H Marine’s ATLAS™ Hydraulic Jack Plate is now available in a “HEAVY DUTY” upgrade. T-H Marine’s ATLAS™ Hydraulic Jack Plate is the #1 selling jack plate in the world and the #1 Choice by fishing professionals and boat manufacturers. With the ATLAS™ HEAVY DUTY, the product is available for applications on even larger outboards, rated for engines up to 400 hp. 5 REASONS YOU SHOULD CHOOSE THE ATLAS™ HYDRAULIC JACK PLATE ATLAS™ is truly the best hydraulic jack plate in the world ATLAS™ is factory installed by more boat manufacturers than any other plate ATLAS™ is used by more professional fisherman than any other hydraulic jack plate ATLAS™ is the #1 selling hydraulic plate in the world – sold & serviced by more outlets ATLAS™ hydraulic actuator is made in the U.S.A. vs. our competitors being from China 6 WAYS THE ATLAS™ CHANGED HYDRAULIC JACK PLATES FOREVER ATLAS™ is made by T-H Marine/CMC, who were the FIRST to offer an actuator inside the jack plate – the competition copied ATLAS™ was the first plate to offer predrilling for shallow water anchors – the competition copied ATLAS™ was the first and only plate that did not require regular grease lubrication – the competition design cannot do that ATLAS™ was the first plate to include a heavy duty safety cable to protect boaters from engine entering cockpit upon failure ATLAS™ was the first plate to offer a very simple actuator replacement in the field ATLAS™ was the first major development in hydraulic jack plates in over a decade – spurring hydraulic jack plate improvement WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

Replacement Relay Harness for Hydraulic Jack Plates 2014+Genuine Replacement Part for Atlas Hydraulic Jack Plate.WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

ATLAS™ 4" Set Back Hydraulic Jack Plate STD PolishedRated for engines up to 300hp or up to 625 pounds dry weight.5 REASONS YOU SHOULD CHOOSE THE ATLAS™ HYDRAULIC JACK PLATE ATLAS™ is truly the best hydraulic jack plate in the world ATLAS™ is factory installed by more boat manufacturers than any other plate ATLAS™ is used by more professional fishermen than any other hydraulic jack plate ATLAS™ is the #1 selling hydraulic plate in the world – sold & serviced by more outlets ATLAS™ hydraulic actuator is made in the U.S.A. vs. our competitors being from China 6 WAYS THE ATLAS™ CHANGED HYDRAULIC JACK PLATES FOREVER ATLAS™ is made by T-H Marine/CMC, which was the FIRST to offer an actuator inside the jack plate – the competition copied ATLAS™ was the first plate to offer predrilling for shallow water anchors – the competition copied ATLAS™ was the first and only plate that did not require regular grease lubrication – the competition design cannot do that ATLAS™ was the first plate to include a heavy-duty safety cable to protect boaters from engine entering the cockpit upon failure ATLAS™ was the first plate to offer a very simple actuator replacement in the field ATLAS™ was the first major development in hydraulic jack plates in over a decade – spurring hydraulic jack plate improvement

Read more less

ATLAS™ 8" Set Back Hydraulic Jack Plate - Heavy DutyT-H Marine’s ATLAS™ Hydraulic Jack Plate is now available in a “HEAVY DUTY” upgrade.T-H Marine’s ATLAS™ Hydraulic Jack Plate is the #1 selling jack plate in the world and the #1 Choice by fishing professionals and boat manufacturers. With the new ATLAS™ HEAVY DUTY, the product is available for applications on even larger outboards, rated for engines up to 400 hp. 5 REASONS YOU SHOULD CHOOSE THE ATLAS™ HYDRAULIC JACK PLATE ATLAS™ is truly the best hydraulic jack plate in the world ATLAS™ is factory installed by more boat manufacturers than any other plate ATLAS™ is used by more professional fisherman than any other hydraulic jack plate ATLAS™ is the #1 selling hydraulic plate in the world – sold & serviced by more outlets ATLAS™ hydraulic actuator is made in the U.S.A. vs. our competitors being from China 6 WAYS THE ATLAS™ CHANGED HYDRAULIC JACK PLATES FOREVER ATLAS™ is made by T-H Marine/CMC, who were the FIRST to offer an actuator inside the jack plate – the competition copied ATLAS™ was the first plate to offer predrilling for shallow water anchors – the competition copied ATLAS™ was the first and only plate that did not require regular grease lubrication – the competition design cannot do that ATLAS™ was the first plate to include a heavy duty safety cable to protect boaters from engine entering cockpit upon failure ATLAS™ was the first plate to offer a very simple actuator replacement in the field ATLAS™ was the first major development in hydraulic jack plates in over a decade – spurring hydraulic jack plate improvement WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

ATLAS™ EDGE 12" Set Back Hydraulic Jack Plate - Classic - Silver HYDRAULIC RISE: 5.75” TOTAL RISE: 8.25” - 9.75” WEIGHT LIMIT: 625 lbs HP: 300 max ATLAS™ EDGE Jack Plate Lifted by Power-Pole®, the next generation of the best-selling ATLAS™ line. Built for anglers who demand more from their equipment, the ATLAS™ EDGE delivers an all-new level of precision, performance, and control – with smarter features designed to make every second on the water count.Smarter Controls, Seamless ExperienceAt the heart of the new ATLAS™ EDGE system is One-Touch Height Control, allowing users to instantly switch between three customizable presets for takeoff, running, and fishing / trailering. With just a single press, boaters can recall their ideal height positions, eliminate guesswork, and maximize efficiency. The Adjustable Speed Settings (Slow, Medium, Fast) offer tailored performance for varying water conditions and preferences, while the Auto Height Mode enables effortless operation — simply tap once to move to one of three custom saved heights; double-tap to get there at full speed.Visibility Meets VersatilityDay or night, the ATLAS™ EDGE stays clear and easy to use thanks to Auto Display Brightness, which adjusts the screen’s visibility based on ambient light. Whether under direct sun or pre-dawn launches, the system delivers information without distraction.Powered by InnovationDesigned in collaboration with Power-Pole®, the ATLAS™ EDGE now features a high performance brushless motor, offering quiet operation, ultra-fast lift speeds, and zero maintenance reliability.Product advantage: Smarter. Faster. SmootherWith its innovative blend of intelligent presets and adaptive speed, the ATLAS™ EDGE sets a new standard for performance on the water. Whether you’re launching, cruising, or dialing in the perfect fishing position, it’s all just one touch away. Brochure (pdf)

Read more less

ATLAS™ EDGE 6" Set Back Hydraulic Jack Plate - Classic - Black HYDRAULIC RISE: 5.75” TOTAL RISE: 8.25” - 9.75” WEIGHT LIMIT: 625 lbs HP: 300 max ATLAS™ EDGE Jack Plate Lifted by Power-Pole®, the next generation of the best-selling ATLAS™ line. Built for anglers who demand more from their equipment, the ATLAS™ EDGE delivers an all-new level of precision, performance, and control – with smarter features designed to make every second on the water count.Smarter Controls, Seamless ExperienceAt the heart of the new ATLAS™ EDGE system is One-Touch Height Control, allowing users to instantly switch between three customizable presets for takeoff, running, and fishing / trailering. With just a single press, boaters can recall their ideal height positions, eliminate guesswork, and maximize efficiency. The Adjustable Speed Settings (Slow, Medium, Fast) offer tailored performance for varying water conditions and preferences, while the Auto Height Mode enables effortless operation — simply tap once to move to one of three custom saved heights; double-tap to get there at full speed.Visibility Meets VersatilityDay or night, the ATLAS™ EDGE stays clear and easy to use thanks to Auto Display Brightness, which adjusts the screen’s visibility based on ambient light. Whether under direct sun or pre-dawn launches, the system delivers information without distraction.Powered by InnovationDesigned in collaboration with Power-Pole®, the ATLAS™ EDGE now features a high performance brushless motor, offering quiet operation, ultra-fast lift speeds, and zero maintenance reliability.Product advantage: Smarter. Faster. SmootherWith its innovative blend of intelligent presets and adaptive speed, the ATLAS™ EDGE sets a new standard for performance on the water. Whether you’re launching, cruising, or dialing in the perfect fishing position, it’s all just one touch away. Brochure (pdf)

Read more less