Boat Outfitting - Jack Plates

ATLAS™ 10" Hydraulic Jack Plate Standard - Black AnodizedThe Atlas revolutionary design meets the demands of today's high performance outboards. The one piece design, featuring the innovative Rod and Slot lifting system, will handle the stresses from the heaviest and most powerful outboards, up to 300 HP or 625 pounds, on the market today. All of the hydraulics are built into the jack eliminating the necessity of installing pumps and reservoirs inside the transom. The all new hydraulic unit is fast too..lifting from bottom to top in 8 seconds!WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

XL 12V Linear ActuatorFor up to 450HP

Read more less

Hardware Kit - 4.5"This kit is for mounting your VOLTIX Series Jack Plate to the transom of your boat.  Supplied with this kit are 6 bolt assemblies that are 4.5″ in length. We supply 6 bolts in our Hardware Kits to accommodate those who wish to utilize the 6-hole mounting pattern.  You may choose to only use 4 bolts to mount your Jack Plate.

Read more less

Hardware Kit - 3"This kit is for mounting your outboard motor to your VOLTIX Series Jack Plate. Supplied with this kit are 6 bolt assemblies that are 3″ in length.We supply 6 bolts in our Hardware Kits to accommodate those who wish to utilize the 6-hole mounting pattern. You may choose to only use 4 bolts to mount your outboard.

Read more less

Tie-Down KitSpecifications: Weight: 3lbs Dimensions: 8 x 8 x 4 inches

Read more less

Dual Paddle Trim SwitchFor complete control of engine trim and tilt, trim tabs, jackplates, and other onboard systems, the innovative Paddle Trim system is the answer.Adaptable to existing front-mount hydraulic and tilt helms, the Paddle Trim is ergonomically designed to allow the driver to make precise adjustments to the attitude of the boat or other systems without removing his hand from the steering wheel.Features: Equipped with two waterproof “MOM.ON-OFF-MOM.ON switch Max load 5 Amp @ 12VDC. Suitable for any kind of steering wheel dish. Max wheel dia. 400 mm (15.7”). Easy to install on the following steering systems: Front and tilt mount hydraulic helms Tilt mount mechanical helms The wiring harness, labels, and mounting hardware kit are included. The mounting plate differs between the front and tilt mount. Installation is ordered separately.

Read more less

Hardware Kit - 6.5"This kit is for mounting your VOLTIX Series Jack Plate to the transom of your boat. Supplied with this kit are 6 bolt assemblies that are 6.5″ in length.We supply 6 bolts in our Hardware Kits to accommodate those who wish to utilize the 6-hole mounting pattern. You may choose to only use 4 bolts to mount your Jack Plate.

Read more less

Single Paddle Trim SwitchFor complete control of engine trim and tilt, trim tabs, jackplates, and other onboard systems, the innovative Paddle Trim system is the answer.Adaptable to existing front-mount hydraulic and tilt helms, the Paddle Trim is ergonomically designed to allow the driver to make precise adjustments to the attitude of the boat or other systems without removing his hand from the steering wheel.Features: Equipped with one waterproof “MOM.ON-OFF-MOM.ON switch Max load 5 Amp @ 12VDC. Suitable for any kind of steering wheel dish. Max wheel dia. 400 mm (15.7”). Easy to install on the following steering systems: Front and tilt mount hydraulic helms Tilt mount mechanical helms The wiring harness, labels, and mounting hardware kit are included. The mounting plate differs between the front and tilt mount. Installation is ordered separately.

Read more less

6" Hole Shot Plate for Z-Lock™ Jack PlateREVOLUTIONARY...SIMPLE...UNIQUE...EXCITING.These are but a few of the comments coming from users of T-H Marine's HOT SHOT™ hole shot plates. This simple but revolutionary plate easily attaches to the bottom of our jack plate to provide an amazing 18 to 20 percent better hole shot. That's 2 to 3 seconds faster out of the hole. Hot Shot™ does this by dramatically reducing water drag on take-off as well as serving as a center trim tab. An added advantage is the ability to stay on a plane and virtually eliminate porpoising at lower speeds.Models available for Z-LOCK™ manual plates.  Features: Provides Improved Hole Shot Reduces Water Drag at Take Off Reduces Porpoising WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

12" Atlas Series Hot Shot™ Jack Plate Hole Shot Plate - VeradoREVOLUTIONARY. SIMPLE. UNIQUE. EXCITING. These are but a few of the comments coming from users of T-H Marine's HOT SHOT™ hole shot plates. This simple-but-revolutionary plate easily attaches to the bottom of our jack plate to provide an amazing 18 to 20 percent better hole shot. That is 2 to 3 seconds faster out of the hole. Hot Shot™ does this by dramatically reducing water drag on take off as well as serving as a center trim tab. An added advantage is the ability to stay on plane and virtually eliminating porpoising at lower speeds.Features: Models available for our ATLAS™ hydraulic jack plates and Z-LOCK™ manual plates.   Models Marked "T" Have side imaging Transducer Cut-Out. Slot fits most Model SI Transducers.  Models to Fit All ATLAS™ Jack Plates (both standard and heavy duty jack plates) Provides Improved Hole Shot Reduces Water Drag at Take Off Reduces Porpoising

Read more less

ATLAS™ Hydraulic Gauge Kit for 4" & 8" ATLAS™ Jack Plate - Black BezelDigital LED Position Gauge for Atlas™ Hydraulic Jack Plates.Features: All Digital Readout Black Face and Stainless Steel FaceGauges Available Outer Bezel available in Stainless Steel or Black Polymer Each Number Indicates 1/4” Rise Numbered from 0 to 20 All AtlasTM Jacks are Pre-drilled to Fit See pictures to the right to view both styles WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less

ATLAS™ Hydraulic Gauge Kit for 4" & 8" ATLAS™ Jack Plates - Stainless Steel BezelDigital LED Position Gauge for Atlas™ Hydraulic Jack Plates.Features: All Digital Readout Black Face and Stainless Steel FaceGauges Available Outer Bezel available in Stainless Steel or Black Polymer Each Number Indicates 1/4” Rise Numbered from 0 to 20 All AtlasTM Jacks are Pre-drilled to Fit See pictures to the right to view both styles WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Read more less