Electrical

BX-2 Junction BoxThis BX Series splashproof box provides secure, protected wiring connections in wheelhouses or below decks and engine rooms. Features: IP rating 54 – “Splashproof” Rugged cast aluminum box with white enamel finish Metal box reduces electrical interference Easy wiring access through multiple grommeted cable entries Supplied with high-quality connector strips – secure wires with compression fittings – no terminals required – see matrix below for connector strips specifications per box Specifications: Number of Connector Strips: 1 Positions per Strip: 12 Max Wire Gauge: 16 Max Amps (per position): 6  Cable Entries: 8 Cable Diameter: 0.37 in. Box Size: 4.4 x 2.4 x 1.2 in. Box Size: 11.2 x 6.1 x 3.1 cm Specifications: Type: Junction Box Box Dimensions: 2"H x 4"W x 8"L WT: 0.45 lbs

Read more less

12-12-6i Power StabilizerFeed sensitive electronics with proper voltage, regardless of the battery condition. This stabilizing converter provides continuous, precisely regulated output over the entire range of a battery’s usable voltage. This prevents subjecting loads to fluctuating input voltage, which can cause shutdown, diminish performance, and possibly damage sensitive circuitry.This converter provides total input/output isolation, virtually eliminating conducted line noise and permitting the connection of negative ground gear to positive or floating ground systems, or vice versa. It can be modified for use as a battery charger, allowing them to maintain a battery at a great distance from the primary voltage source, providing reserve power if the main source fails. The rugged anodized aluminum case is ideal for marine applications.Application Benefits Include: Operate electronics at optimal input voltage, even from nearly drained batteries Boost voltage to compensate for voltage drops in long wire runs from batteries Eliminate voltage drops during momentary high current drain from batteries, as during engine start Eliminate voltage fluctuation from charge sources Eliminate voltage overshoot due to sudden removal of high current load Specifications: Input Voltage: 10-16 Input Amps: 8 Output Voltage: 13.6 Output Amps (Intermittent): 6 Output Amps (Continuous): 6 Case Size (H x W x D): 6.5 x 4.0 x 1.75 inches (6.8 x 10.2 x 4.5 centimeters) Weight: 2 lb. (.9 kg) Output: 12 or 24V, nominal, see matrix Ripple: 150 mV P-P maximum Regulation: 1% Line/Load Duty Cycle Ratings: Intermittent: 20 minutes max on time, 20% duty. The current limit is set at approx. 105% of intermittent rating. Continuous: 24 hours, 100% duty Idle Current: Less than 100 mA (including power “ON” light ) Operating Temp: 0-50 degrees C, Derate Linearly From 100% @ 40 degrees C To 50% @ 50 degrees C. Thermal shutdown @ 70 degrees C Case Temperature. Switching Frequency: 40 kHz. Efficiency: 85% – Typical. Isolation – Output/Chassis; Input/chassis: 250 VDC Mechanical Specifications: Anodized aluminum heat sink case Front panel terminal block Heavy-duty mounting flange Conformal-coated PC board Options/Factory Modifications: Operation as a battery charger (contact factory) Parallel/redundant operation (contact factory) High-vibration mounting kit Non-standard output voltage (contact factory) Option: Extreme Vibration Mounting KitThe Extreme Vibration Mounting Kit is available to protect NEWMAR power converters from the extreme stresses of shock and vibration when mounted on high-vibration vehicles.The kit (pictured here) replaces the standard vibration kit provided with the unit and fits into the unit’s mounting flange to act as a “super shock absorber” for electronics in high-vibration applications. It is available to fit all NEWMAR units from 2 to 70 lbs. Specify KIT–L for units that weigh 2–15 lbs. and Kit–H for units that weigh 16-70 lbs.This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Read more less

BB-8 Bus BarIdeal as a DC ground tie point or positive bus, this heavy-duty, 500-amp-rated bus bar assembly features 5/16 in. studs on 1 in. center in 1/4 in. thick copper bar for common connection or distribution of large wire gauges.Features: Accommodate 5/16" ring terminals Insulated base (reinforced nylon resin with a clear protective cover) Specifications: Quantity of 5/16" Studs: 8 Size (inches): 9-1/16” x 1-1/2”

Read more less

NS-12-20 StartGuardThe abrupt DC system voltage drop that accompanies engine starting can cause micro-processor-driven electronics aboard vehicles or vessels to "dump" programmed memory. StartGuard solves these problems by providing supplemental power to sensitive electronics while the engines are cranking. Newmar's NS-12-20 StartGuard supplies backup power for electronics during engine start. MountingMount the StartGuard in any convenient location, such as under the dash or console, using the four mounting screws provided or #10 bolts.WiringInput from the power source to the electronics must be routed through the StartGuard. Specifications: Input Voltage: 13.8-14.8 VDC nominal, 15.5 VDC Max Relay Activation Input Voltage: 7-15 VDC Output: 20 Amps Max Battery: 12 VDC, 4.0 Amp/Hour, Sealed Rechargeable, 3-5 Year Life (Typical) Backup Capacity (Fully Charged): 20 Amps for one minute/18 Amps for 2 minutes Operating Temperature Range: 0-40 degrees Celsius Winter Storage Temperature Range: -20 degrees to +40 degrees Celsius Dimensions: 8.25" x 4.9" x 3.5" Weight: 5.5 lbs This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Read more less

ACCY-IBX Blank PanelThis versatile panel is ideal when only a limited number of electrical circuits are needed or for larger systems where their modular design makes for an easy and attractive expansion of existing system capacity.Stock panels with breakers installed come standard with DC indicator lights but may be specially ordered with AC indicator lights. Blank versions of the panels have all the necessary hardware to install indicator lights and breakers. All panels are provided with a circuit identification label set of 22 common on-board electrical functions. ACCY-IBX is a blank version of ACCY-IX. No breakers or indicator lights are provided. Label set, indicator light, and breaker mounting hardware are provided.Specifications: Cut-Out Dimensions: 4 x 6 inches (10.2 x 15.2 centimeters) Weight: 1 lb.

Read more less

BX-3 Junction BoxThis BX Series splashproof box provides secure, protected wiring connections in wheelhouses or below decks and engine rooms. Features: IP rating 54 – “Splashproof” Rugged cast aluminum box with white enamel finish Metal box reduces electrical interference Easy wiring access through multiple grommeted cable entries Supplied with high-quality connector strips – secure wires with compression fittings – no terminals required – see matrix below for connector strips specifications per box Specifications: Number of Connector Strips: 2 Positions per Strip: 11 Max Wire Gauge: 14 Max Amps (per position): 10  Cable Entries: 2 Cable Diameter: 0.59 in. Box Size: 4.7 x 3.7 x 1.3 in. Box Size: 11.9 x 9.4 x 3.3 cm Specifications: Type: Junction Box Box Dimensions: 2"H x 6"W x 9"L WT: 0.7 lbs

Read more less

BB-2 Bus BarIdeal as a DC ground tie point or positive bus, this heavy-duty, 500-amp-rated bus bar assembly features 5/16 in. studs on 1 in. center in 1/4 in. thick copper bar for common connection or distribution of large wire gauges.Features: Accommodate 5/16" ring terminals Insulated base (reinforced nylon resin with a clear protective cover) Specifications: Quantity of 5/16" Studs: 2 Size (inches): 1/16" x 1 1/2"

Read more less

ACCY-IX Blank PanelThis versatile panel is ideal when only a limited number of electrical circuits are needed or for larger systems where their modular design makes for an easy and attractive expansion of existing system capacity.Stock panels with breakers installed come standard with DC indicator lights but may be specially ordered with AC indicator lights. Blank versions of the panels have all the necessary hardware to install indicator lights and breakers. All panels are provided with a circuit identification label set of 22 common on-board electrical functions. ACCY-IX has an 8-breaker capacity, with 5 installed standard; 2-5A, 1-10A, 1-15A, 1-20A, or specify. 8 DC circuit “ON” indicator lights installed, and AC indicator lights installed on a special order basis. LS-1 label set is included.Specifications: Cut-Out Dimensions: 4 x 6 inches (10.2 x 15.2 centimeters) Weight: 2 lbs. Specifications: Max Breaker Quantity: 8 Box Dimensions: 6"H x 8"W x 12"L WT: 2.2 lbs

Read more less

Power-Pac 7AH Power SupplyThe 12V DC power supply features built-in backup batteries, which are charged during normal operation and then continue to power radios and critical navigation equipment when AC power is lost. The Power-Pac is ideal for commercial vessels, work boats, and yachts.The Power-Pac’s highly regulated, low-rising 10-amp output powers radios and other sensitive communications equipment without causing RF or audio interference. At the same time, it floats and charges one or two (depending on the model) built-in 7-amp/hour backup batteries. These are kept at peak charge during the normal functioning of the unit when AC is being supplied. In the event of a loss of AC power, the internal batteries automatically take over to power communication equipment, providing a true uninterruptible DC source.Features: Highly regulated, low ripple, noise-free 12-volt output Built-in, “on-line” stand-by battery provides immediate backup power in case of AC power loss Internal mounting space and terminals for conversion of the 7 A/H model into the 14 A/H model Output “Normal” indicator L.E.D. “Back-up power only” warning light Audible and visual low battery (10.7 VDC) voltage indicators Low battery warning buzzer mute switch Automatic low battery (10.3 VDC) voltage disconnect Low voltage disconnect override button Over-voltage protection Current limit protection Input/output fused Separate output terminals are provided for charging external batteries 115/230 50-60 Hz input, selected by a slide switch on the rear panel Specifications: Battery Capacity: 7 amp/hour   Case Size (H x W x D): 5.3 x 9.0 x 10.5 inches (13.3 x 22.9 x 26.7 centimeters)   Weight: 18 lbs. (8.2 kg) Input: 115/230 VAC, 50-60 Hz. Output: 13.6 VDC @ 5A cont., 10A Int. Regulation: 1% line and load Ripple: 1% P-P Operating Temp: 0-40 degrees C With a 7 Amp/Hour Battery Installed, the Unit Provides Approximately the Following Power. *7 Amps for 40 Min. 10 amps for 20 min. 15 amps for 10 min. 20 amps for 4 min. *Assuming battery at full charge when a.c. power failed.The Power-Pac 7 A/H (single battery model) can power a 25-watt transceiver for up to 3 hours, based on a 20% transmit/receive duty cycle. Power-Pac 14 A/H can provide the same service for up to 6 hours. Provision is made for expanding backup power up to twelve hours (in this example, longer under lesser loads) with the installation of additional externally wired batteries (total 28 amps/hours max.). Batteries are automatically recharged when the AC is restored.The operator is kept informed of all important functions, such as AC input, DC output, and battery status, with front panel indicator lights and a low battery warning buzzer.Protection: AC Input fuse Internal and external Battery fuses Over Voltage Current Limit Automatic Thermal Shutdown Low Battery Disconnect Mechanical Details: Vinyl Laminated aluminum case 6’ standard AC power cord Ac input selector switch Battery Details: Sealed Lead Acid, Deep-cycle. Certified by DOT and IATA for shipment by Air Weight per 7 AH Battery; 6 lbs. Size (inch): 6” x 3.75” x 2.5” Options: Form C AC Failure Contacts (Contact factory for details) Extra batteries, sold separately 7 A/H increments; each Power Pac will accommodate 28 A/H max. (14 internal, 14 external) This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns. Quick Guide (pdf)Owner's Manual (pdf)

Read more less

Stainless Steel Low-Profile Multi Cable Seal for Cables Up to 15mmThe DS-LP-MULTI-S Low-Profile Cable Seal is engineered to effortlessly accommodate multiple cables up to Ø15mm (0.59"), ensuring a seamless and impact-resistant solution.Premium ConstructionCrafted with attention to detail, its marine-grade 316 stainless steel construction is not only aesthetically pleasing but also built to thrive in the outdoor environment. 316 stainless steel has exceptional corrosion resistance and durability, making it the perfect choice for withstanding the elements and ensuring the installation remains intact even in the harshest conditions. The fine finish of Scanstrut's 316 stainless steel design adds a touch of sophistication to the installation, elevating both the form and function of the cable installation.Low-Profile DesignThe Scanstrut slimline design was purpose-built to reduce the overall mounting height of the cable seal by 61% in comparison to Scanstrut's DS-MULTI seal. This translates to a clean, flush, more refined look.Watertight InstallationAchieve peace of mind with Scanstrut watertight installation. The tapered bung forms a secure seal, while every unit has a closed-cell base seal for 100% waterproof assurance. All models have undergone rigorous IP68 testing and approval to ensure they are outdoor-ready.Effortless and Repeat InstallationsFeaturing captive nuts to simplify assembly and allow for reliable repeat installations. Each unit is supplied with pre-drilled and blank bungs, streamlining the setup process. Also, there's no need to remove the cable connector during installation, thanks to the convenient split-seal option.Features: IP68 Waterproof Designed for multiple cables up to 15mm (0.59”). UV Resistant Constructed from marine-grade 316 stainless steel No messy sealant, ensuring a tidy finish Simplified installation that saves you time and effort Guaranteed 100% watertight seal Perfect for solar panels, light bars, rooftop electronics, and more Each cable seal is installed by using a hole saw, keeping seal technology below the mounting surface Specifications: Type: Deck Seal Box Dimensions: 1"H x 4"W x 9"L WT: 0.75 lbs UPC: 5060114798656 Quick Guide (pdf)

Read more less

Black Anodized Aluminum Low-Profile Cable SealThe DS-LP-16-BLK Low-Profile Cable Seal is engineered to effortlessly accommodate cables ranging from 2–8 mm (0.08"–0.35") and connectors up to Ø16mm (0.63"), ensuring a seamless and impact-resistant solution.Premium ConstructionCrafted with attention to detail, its marine-grade aluminum construction is not only aesthetically pleasing but also built to thrive in the outdoor environment. Aluminum has exceptional corrosion resistance and durability, making it the perfect choice for withstanding the elements and ensuring the installation remains intact even in the harshest conditions. The fine finish of the aluminum design adds a touch of sophistication to the installation, elevating both the form and function of the cable installation.Low-Profile DesignThe Scanstrut slimline design was purpose-built to reduce the overall mounting height of the cable seal by 73% in comparison to Scanstrut's DS16-P-BLK seal. This translates to a clean, flush, more refined look.Watertight InstallationAchieve peace of mind with Scanstrut watertight installation. The tapered bung forms a secure seal, while every unit has a closed-cell base seal for 100% waterproof assurance. All models have undergone rigorous IP68 testing and approval to ensure they are outdoor-ready.Effortless and Repeat InstallationsFeaturing captive nuts to simplify assembly and allow for reliable repeat installations. Each unit is supplied with pre-drilled and blank bungs, streamlining the setup process. Also, there's no need to remove the cable connector during installation, thanks to the convenient split-seal option.Features: The cable seal is black  IP68 Waterproof Designed for 2-8mm cables (0.08"-0.35") UV Resistant Constructed from marine-grade aluminum No messy sealant, ensuring a tidy finish Simplified installation that saves you time and effort Guaranteed 100% watertight seal Perfect for solar panels, light bars, rooftop electronics, and more Each cable seal is installed by using a hole saw keeping seal technology below the mounting surface Specifications: Type: Deck Seal Box Dimensions: 1"H x 4"W x 9"L WT: 0.2 lbs UPC: 5060114798571 Quick Guide (pdf)

Read more less

Black Anodized Aluminum Low-Profile Cable Seal for Cables 9-14mm & Connectors Up to Ø21mmThe DS-LP-21B-BLK Low-Profile Cable Seal is engineered to effortlessly accommodate cables ranging from 9–14 mm (0.3–0.5") and connectors up to Ø21mm (0.83"), ensuring a seamless and impact-resistant solution.Premium ConstructionCrafted with attention to detail, its marine-grade aluminum construction is not only aesthetically pleasing but also built to thrive in the outdoor environment. Aluminum has exceptional corrosion resistance and durability, making it the perfect choice for withstanding the elements and ensuring the installation remains intact even in the harshest conditions. The fine finish of the aluminum design adds a touch of sophistication to the installation, elevating both the form and function of the cable installation.Low-Profile DesignThe Scanstrut slimline design was purpose-built to reduce the overall mounting height of the cable seal by 68% in comparison to Scanstrut's DS21B-P-BLK seal. This translates to a clean, flush, more refined look.Watertight InstallationAchieve peace of mind with Scanstrut watertight installation. The tapered bung forms a secure seal, while every unit has a closed-cell base seal for 100% waterproof assurance. All models have undergone rigorous IP68 testing and approval to ensure they are outdoor-ready.Effortless and Repeat InstallationsFeaturing captive nuts to simplify assembly and allow for reliable repeat installations. Each unit is supplied with pre-drilled and blank bungs, streamlining the setup process. Also, there's no need to remove the cable connector during installation, thanks to the convenient split-seal option.Features: The cable seal is black IP68 Waterproof Designed for 9-14mm cables (0.35"–0.55") UV Resistant Constructed from marine-grade aluminium No messy sealant, ensuring a tidy finish Simplified installation that saves you time and effort Guaranteed 100% watertight seal Perfect for solar panels, light bars, rooftop electronics, and more Each cable seal is installed by using a hole saw, keeping seal technology below the mounting surface Specifications: Type: Deck Seal Box Dimensions: 1"H x 4"W x 9"L WT: 0.25 lbs UPC: 5060114798779 Quick Guide (pdf)

Read more less